Polk Audio SurroundBar One-Step Manual Del Usuario página 9

FINE TUNING YOUR SurroundBar One-Step
The next thing you'll want to do is adjust the Wireless Subwoofer
to blend with your SurroundBar One-Step speaker. This will
ensure the system produces the best sound.
Set the Wireless Subwoofer's volume to the middle of its
range. Now play a variety of source material—some music,
a movie sound track with great special effects, a movie chapter
or a part of a concert in which people are speaking. Adjust
the volume until what you hear sounds natural to you in your
normal viewing location.
HOW TO SET UP A REMOTE CONTROL
FOR YOUR SurroundBar One-Step
If your existing TV or cable/satellite remote does not change
the volume of the SurroundBar One-Step, then your SurroundBar
One-Step is connected to a "constant level" (or "fixed") output.
This means you'll want to program your SurroundBar One-Step
to respond to the remote control codes of your existing remote
or any other remote control you want to use. Ideally, you will
need only one remote for your system.
Example: To have your SurroundBar One-Step learn
the "mute" command of your remote control:
1 Press and hold the "REMOTE" button until the status light
turns orange and starts blinking.
MUTE
2 Press the button on the SurroundBar One-Step that you want
to program to respond to your remote control—in this case
the "MUTE" button. The status indicator should stop blinking
and turn a steady orange.
MUTE
3 Point your remote control at the front of the SurroundBar
One-Step from approximately 12" (30cm) away. Press and hold
the mute button on your remote for a full second then release
the button for a full second. Repeat the press and release
sequence until the status indicator starts blinking green.
If your SurroundBar One-Step fails to learn the remote control
signal it will blink red. If this occurs, repeat steps 1 - 3. Be sure
to keep the remote steady and press the button slowly.
Repeat the process for the other buttons on your remote
control that you want your SurroundBar One-Step to learn.
REMOTE
REMOTE
Customer Service Hours of Operation: Monday-Friday, 9
Remember—The SurroundBar One-Step can learn to respond to
almost any button on almost any remote. Decide what remote
you want to use—television, satellite receiver, cable control
box, etc.—and program your SurroundBar One-Step to respond
to the buttons you want to use.
If you make a mistake, or want to erase the remote control
programming of the SurroundBar One-Step, here's what you do:
1 Press and hold the "MUTE" and "REMOTE"
buttons simultaneously.
MUTE
2 The status light flashes red and orange for several seconds.
NOTE: This procedure removes ALL of your SurroundBar
One-Step remote control programming. If you only need to
change the programming for some of the SurroundBar One-Step
buttons, follow the three steps in the left-hand column to redo
any previous programming.
DETAILS ABOUT SurroundBar One-Step
Power—The power switches on the back of the SurroundBar
One-Step and Wireless Subwoofer can be left on. The
SurroundBar One-Step has an automatic power standby system.
After about 15 minutes of inactivity, the amplifiers will shut down.
As soon as a signal is applied to the inputs of the SurroundBar
One-Step, the amplifiers automatically turn on again.
Channel ID Switches—Both the SurroundBar One-Step
and Wireless Subwoofer have channel ID switches. The
switch settings change the frequency of the wireless signal
the SurroundBar One-Step sends to the Wireless Subwoofer.
The two switches must be set to the same position.
Example: Switch Settings
SurroundBar
One-Step
CHANNEL ID
1 2 3 4
You'll probably never need to adjust these switches. If you
put more than one SurroundBar One-Step system in your
home, use different channel ID switch settings so the
systems don't interfere with each other.
Gain Level Switch—This changes the input sensitivity of
your SurroundBar One-Step. If the output of your television
is too low, you may need to increase the gain level to make
the SurroundBar One-Step play louder. If you hear distortion
you should decrease the gain level to make it sound better.
REMOTE
Wireless
Subwoofer
CHANNEL ID
1 2 3 4
-6 [email protected]
AM PM EST
9