Description Of The Hood - ELICA TENDER Serie Montaje Y Modo De Empleo

página de 105

/ 105
Contenido
Tabla de contenido

Tabla de contenido

Idiomas disponibles

a plug connect the hood to a socket in compliance with current

regulations and positioned in an accessible area. If it not fitted

with a plug (direct mains connection) or if the plug is not

located in an accessible area apply a double pole switch in

accordance with standards which assures the complete

disconnection of the mains under conditions relating to over-

current category III, in accordance with installation

instructions.

Warning! Before re-connecting the hood circuit to the mains

supply and checking the efficient function, always check that

the mains cable is correctly assembled.

Mounting

Before beginning installation:

•

Check that the product purchased is of a suitable size for

the chosen installation area.

•

To facilitate installation, remove the fat filters and the

other parts allowed and described here, dismantle and

mount it.

To remove see also the relative paragraphs.

•

Remove the active carbon (*) filter/s if supplied (see also

relative paragraph). This/these is/are to be mounted only

if you want lo use the hood in the filtering version.

•

Check (for transport reasons) that there is no other

supplied material inside the hood (e.g. packets with

screws (*), guarantees (*), etc.), eventually removing

them and keeping them.

•

If possible, disconnect and move freestanding or slide-in

range from cabinet opening to provide easier access to

rear wall/ceiling. Otherwise put a thick, protective

covering over countertop, cooktop or range to protect

from damage and debris. Select a flat surface for

assembling the unit. Cover that surface with a protective

covering and place all canopy hood parts and hardware

in it.

•

Disconnect the hood during electrical connection, by

turning the home mains switch off.

•

In addition check whether near the installation area of the

hood (in the area accessible also with the hood mounted)

an electric socket is available and it is possible to

connect a fumes discharge device to the outside (only

suction version).

•

Carry out all the masonry work necessary (e.g.

installation of an electric socket and/or a hole for the

passage of the discharge tube).

Expansion wall plugs are provided to secure the hood to most

types of walls/ceilings. However, a qualified technician must

verify suitability of the materials in accordance with the type of

wall/ceiling. The wall/ceiling must be strong enough to take

the weight of the hood. Do not tile, grout or silicone this

appliance to the wall. Surface mounting only.

Installation wall model

Fig. 5

Using a pencil, draw a line on the wall, extending up to

the ceiling, to mark the centre.

installation.

Rest the drilling template against the wall: the vertical

centre line printed on the drilling template must

This will facilitate

correspond to the centre line drawn on the wall, and the

bottom edge of the drilling template must correspond to

the bottom edge of the hood.

Place the lower support bracket on the perforation

diagram making it coincide with the traced triangle, mark

the two external holes and perforate.

Note: Always make the holes indicated on the template.

The upper 2 are for hooking the hood up while the lower

holes (generally 1 central or more lateral) are for the

definitive and safety fixing.

Remove the perforation diagram, insert the wall-dowels

and fix the support bracket of the hood with two 5x45 mm

screws.

Apply the flues support bracket G to the wall adherent to

the ceiling, use the flues support bracket as a perforation

diagram (if present, the small slot on the support must

coincide with the line drawn previously on the wall) and

mark two holes with a pencil. Make the holes (Ø8mm),

and insert 2 dowels.

Fix the chimney support bracket to the wall using two

5x45mm screws.

Hang the hood onto the lower bracket.

Adjust the distance of the hood from the wall.

Adjust the horizontal position of the hood.

Fix the hood into its final position on the wall

(ABSOLUTELY ESSENTIAL).

10. Connect a pipe (pipe and pipe clamps not provided, to be

purchased separately) for discharge of fumes to the

connection ring located over the suction motor unit.

If the hood is to be used in ducting version, the other end

of the pipe must be connected to a device expelling the

fumes to the outside. If the hood is to be used in filter

version, then fix the deflector F to the chimney support

bracket G and connect the other extremity of the pipe to

the connection ring placed on the deflector F.

11. Connect the electricity.

12. Apply the chimney stacks and fasten them at the top to

the chimney support „G" (12b) using 2 screws (12a)

13. Slide the bottom section of the chimney down until it

completely covers the suction unit and slots into the

housing provided on top of the hood.

Remount the carbon filter frame and the fat/s filter/s and check

the perfect functioning of the hood.