How To Use - McCulloch Orkan 2200 Manual De Instrucciones

• Switch off and disconnect from the mains
electricity supply BEFORE REMOVING OR
REPLACING the fully assembled debris
bag.
• The cutting head and cutting line
continue to rotate after your Gardenvac
has been switched off.
To Fit Assembled Debris Bag To Product (E)
IMPORTANT Do not squeeze the trigger
when fitting the debris bag (E1)
1. Ensure debris fin is horizontal (E2) as
illustrated in fig E.
2. Locate bag frame into clip on the underside
of product. (E3).
3. Lift handle towards product until bag latch
locates and click into place (E4).
To Remove Debris Bag From Product (F)
1. Gently press bag latch (F1) down. See fig F.
2. Lower handle of bag frame away from
product.
3. Move bag frame forward.
WARNING The use of eye protection is
recommended. The use of ear protection is
recommended. To prevent dust irritation, the
wearing of a face-mask is recommended.
Never point your Gardenvac at bystanders.
Do not use your Gardenvac in the rain. Do
not leave your Gardenvac outdoors while it is
raining.
IMPORTANT!: YOUR GARDENVAC WILL NOT
OPERATE UNTIL THE FULLY ASSEMBLED
DEBRIS BAG AND FRAME ARE PROPERLY
FITTED.
BEFORE USE: E
NSURE THERE ARE
BETWEEN THE DEBRIS BAG AND THE PRODUCT
•
The Gardenvac has 3 modes of operation.
•
These can be selected by moving the mode
indicator to adjust the nozzle position for
blow, vacuum or jet vacuum mode.
•
In vacuum and jet vacuum modes the
Gardenvac will shred leaves etc.
M - BLOW
Position 1 - Blow Mode
The Gardenvac will blow debris from patios,
paths, driveways, lawns, bushes, borders etc.
Using As A Blower
1. Select position 1 on the mode indicator. See
fig M.
2. Point nozzle towards the ground.
3. To start squeeze trigger.
4. Stand back from debris to be cleared.
5. Point nozzle towards the debris and slowly
approach.
6. To stop release trigger.
ENGLISH - 3
ASSEMBLY INSRUCTIONS
Fitting the Handle Bolt (G)
1. Place handle bolt into the location slot on the
2. Repeat on the other side.
Fitting the Handle (H)
1. Locate handle onto handle bolts on each
2. Secure handle by turning handle knobs
3. The handle can be adjusted by turning
Fitting The Shoulder Harness (J), (K) & (L).
1. Thread strap through the slots in the handle
2. Thread strap through the buckle. See fig K1.

HOW TO USE

N- VACUUM
Position 2 - Vacuum Mode
In this position your Gardenvac will pick up
leaves, paper, rubbish, cans etc.
IMPORTANT: R
V
ACUUMING
Using As A Vacuum
1. Select position 2 on the mode indicator. See
2. Position nozzle slightly above the debris,
NO GAPS
3. Do not force the nozzle into the debris as
.
4. To stop release the trigger.
P - JET VACUUM
Position 3 - Jet Vacuum Mode
This position is intended to be used to collect
debris which is damp or stubborn. It directs
a small jet of air towards the ground which
will loosen stubborn material.
Using As A Jet Vacuum
1. Select position 3 on the mode indicator. See
2. Position the nozzle above and slightly
3. Slowly move the nozzle back over the
4. To stop release the trigger.
product and slide into place.
See Fig. G.
side of the product.
clockwise. See Fig H.
handle knobs 3 full turns anti-clockwise,
moving handle to position required and
re-securing handle as described in 2.
See fig J.
N
EMOVE YLON
C
ANS
fig N.
squeeze the trigger and move slowly back
and forth.
this will impair performance.
fig P.
forward of the debris and squeeze the
trigger.
debris. This allows a jet of air to lift the
debris from the ground.
L BEFORE
INE