Troubleshooting; Protecting The Environment; Ec Declaration Of Conformity - Stanley Fatmax FMCS701 Manual De Instrucciones

ENGLISH

Troubleshooting

Problem Possible Cause
Battery not installed.
Saw will not
Battery not charged.
start.
Brushes worn out
Dull blade.
Blade mounted
backwards.
Saw makes
unsatisfactory
cuts.
Gum or pitch on
blade.
Incorrect blade for
work being done.
Work light is
Battery not charged
flashing.
Saw not mounted
securely to stand or
work bench.
Machine
vibrates Stand or bench on
excessively. uneven floor.
Damaged saw
blade.
Mitre scale not
adjusted correctly.
Blade is not square
to fence.
Does not
Blade is not
make accurate
perpendicular to
mitre cuts.
table.
Work piece moving
Kerf plate worn or
damaged.
Material Cutting bowed
pinches blade. material.
Z

Protecting the environment

Separate collection. Products and batteries marked
with this symbol must not be disposed of with normal
household waste.
Products and batteries contain materials that can be recov-
ered or recycled reducing the demand for raw materials.
Please recycle electrical products and batteries according to
local provisions. Further information is available at
www.2helpU.com
20
(Original instructions)
Solution
Install battery. Refer to Installing
and Removing Battery Pack.
Charge battery. Refer to Charging
Procedure.
Have brushes replaced by
authorised service centre.
Replace blade. Refer to Changing
or Installing a New Saw Blade.
Turn blade around. Refer to
Changing or Installing a New Saw
Blade.
Remove blade and clean with
coarse steel wool and turpentine or
household oven cleaner.
Change the blade type.
Charge battery. Refer to Charging
Procedure.
Tighten all mounting hardware.
Refer to Bench Mounting
Reposition on flat level surface.
Replace blade. Refer to Changing
or Installing a New Saw Blade.
Check and adjust. Refer to Mitre
Scale Adjustment under
Adjustments.
Check and adjust. Refer to Mitre
Scale Adjustment under
Adjustments.
Check and adjust fence. Refer to
Bevel Square to Table Adjustment
under Adjustments.
Clamp work piece securely to fence
or glue 120 grit sandpaper to fence
with rubber cement.
Take to authorised service centre.
Refer to Bowed Material under
Special Cuts.
Technical data
Voltage
Speed
Blade outer diameter
Bore diameter
Blade max. kerf
Weight without battery
Blade thickness
Mitre (max. positions)
Bevel (max. positions)
horizontal
0 deg. mitre
vertical
horizontal
45 deg. mitre right
vertical
horizontal
45 deg. mitre left
vertical
horizontal
45 deg. bevel left
vertical
Charger
Input voltage
V
AC
Output voltage
V
DC
Output current
A
Approx. charge time
Mins
Battery FMC689L
Voltage V 18
DC
Capacity Ah 1.5
Type Li-Ion
Level of sound pressure according to EN 62841:
L (sound pressure) 83.0 dB(A), Uncertainty (K) 3 dB(A)
pA
L (sound power) 94.5 dB(A), Uncertainty (K) 3 dB(A)
WA
%

EC declaration of conformity

MACHINERY DIRECTIVE
FMCS701 Sliding Compound Mitre Saw
Stanley Europe declares that these products described under
"technical data" are in compliance with:
EN62841-1:2015, EN62841-3-9:2015+A11:2017
FMCS701 (H1)
V 18
/min 3,800
mm 190
mm 16
mm 1.8
kg 10
mm 1.0
° 47
° 47
mm 50 x 216
mm 90 x 15
mm 50 x 152
mm 90 x 15
mm 50 x 152
mm 90 x 15
mm 50 x 152
mm 50 x 15
905998** typ. 1 906086** typ. 1
230 230
18 18
1 2
90 - 240 45 - 120
FMC687L FMC688L
18 18
2.0 4.0
Li-Ion Li-Ion