Important Charging Notes - Stanley Fatmax FMCW220 Traducción De Las Instrucciones Originales

ENGLISH
Read the instruction manual before use.
Electrical safety
#
Your charger is double insulated; therefore no
earth wire is required. Always check that the
mains voltage corresponds to the voltage on the
rating plate. Never attempt to replace the charger
unit with a regular mains plug.
If the supply cord is damaged, it must be replaced by the
u
manufacturer or an authorised BLACK+DECKER Centre
in order to avoid a hazard.
Features
This tool includes some or all of the following features.
1. Handle
2. On/off button
3. Sanding pad
4. Battery
5. Dust extraction outlet
6. Charger
Charging procedure (fig. A)
Stanley FatMax chargers are designed to charge Stanley
FatMax battery packs.
Plug the charger (6) into an appropriate outlet before
u
inserting the battery pack (4).
Insert the battery pack (4) into the charger (6) as shown in
u
figure A.
The LED (6a) will flash indicating that the battery is being
u
charged.
The completion of charge is indicated by the LED (6a)
u
remaining on continuously. The pack is fully charged and
may be used at this time or left on the charger.
Note: Recharge discharged batteries as soon as possible
after use or battery life may be greatly diminished. For longest
battery life, do not discharge batteries fully.
It is recommended that the batteries be recharged after each
use.
Leaving the battery in the charger
The charger (6) and battery pack (4) can be left connected
with the LED glowing indefinitely. The charger will keep the
battery pack fresh and fully charged.

Important charging notes

Longest life and best performance can be obtained if
u
the battery pack is charged when the air temperature is
between 65°F and 75°F (18°- 24°C). DO NOT charge the
battery pack in an air temperature below +40°F (+4.5°C),
or above +105°F (+40.5°C). This is important and will
prevent serious damage to the battery pack.
6
(Original instructions)
The charger and battery pack may become warm to touch
u
while charging. This is a normal condition, and does not
indicate a problem. To facilitate the cooling of the battery
pack after use, avoid placing the charger or battery pack
in a warm environment such as in a metal shed, or an
uninsulated trailer.
If the battery pack does not charge properly:
u
Check current at receptacle by plugging in a lamp or
u
other appliance.
Check to see if receptacle is connected to a light switch
u
which turns power off when you turn out the lights.
Move charger and battery pack to a location where the
u
surrounding air temperature is approximately 65°F
- 75°F (18°- 24°C).
If charging problems persist, take the tool, battery pack
u
and charger to your local service center.
The battery pack should be recharged when it fails to
u
produce sufficient power on jobs which were easily done
previously. DO NOT CONTINUE to use under these
conditions. Follow the charging procedure. You may also
charge a partially used pack whenever you desire with no
adverse affect on the battery pack.
Foreign materials of a conductive nature such as, but
u
not limited to, steel wool, aluminium foil, or any buildup
of metallic particles should be kept away from charger
cavities. Always unplug the charger from the power supply
when there is no battery pack in the cavity. Unplug charger
before attempting to clean.
Do not freeze or immerse charger in water or any other
u
liquid.
Warning! Do not allow any liquid to get inside charger. Never
attempt to open the battery pack for any reason. If the plastic
housing of the battery pack breaks or cracks, return to a
service center for recycling.
Charger Diagnostics (fig. B)
Refer to the indicators in figure B for the charge status of the
battery pack.
Bad Battery
If you see a bad battery blink pattern, do not continue
to charge this battery. Return it to a service center or a
collection site for recycling.
Hot/Cold Pack Delay
When the charger detects a battery pack that is too hot
or too cold, it automatically starts a Hot/Cold Pack Delay,
suspending charging until the battery pack has reached an
appropriate temperature. The charger then automatically
switches to the pack charging mode. This feature ensures
maximum battery pack life. A cold battery pack will charge at a
slower rate than a warm battery pack. The pack will charge at