(En) System Exclusive Data Sheet; Command Table - Behringer POLY D Guia De Inicio Rapido

72
POLY D
POLY D System Exclusive Data Sheet

(EN) System Exclusive Data Sheet

The "Synthtool.exe" application allows you to select the MIDI channel number and to set and adjust various parameters of the POLY D to suit your preferences.
Parameters can also be accessed via MIDI system Exclusive (SysEx) commands. Please see the information shown below.
SETTING VALUES VIA SYSEX
Use the following data format to set global value using a SysEx message.
F0 00 20 32 00 01 0c aa bb cc D0 ... Dn F7
00 20 32 = Manufacture SYSEX ID number (Behringer GmbH)
00 01 0c = Model ID for POLY D
aa = Device ID: 00-0x7F (must match hardware device ID), or 0x00 to address all devices.
bb = Packet Number
cc = Sub packet number (maybe absent for some message).
D0..Dn = Packet payload

COMMAND TABLE

Packet Number SysEx Packet
00 F0 00 20 32 00 01 0c DID 00 nn F7
0E F0 00 20 32 00 01 0c DID 0E 01 nn mm F7
0F F0 00 20 32 00 01 0c DID 0F nn F7
10 F0 00 20 32 00 01 0c DID 10 nn mm pp F7
11 F0 00 20 32 00 01 0c DID 11 nn mm F7
12 F0 00 20 32 00 01 0c DID 12 nn F7
14 F0 00 20 32 00 01 0c DID 14 nn mm F7
15 F0 00 20 32 00 01 0c DID 15 nn F7
16 F0 00 20 32 00 01 0c DID 16 nn F7
17 F0 00 20 32 00 01 0c DID 17 nn F7
19 F0 00 20 32 00 01 0c DID 19 nn F7
1A F0 00 20 32 00 01 0c DID 1A nn F7
1B F0 00 20 32 00 01 0c DID 1B nn F7
20 F0 00 20 32 00 01 0c DID 20 nn F7
21 F0 00 20 32 00 01 0c DID 21 nn F7
22 F0 00 20 32 00 01 0c DID 22 nn F7
23 F0 00 20 32 00 01 0c DID 23 nn F7
24 F0 00 20 32 00 01 0c DID 24 nn F7
25 F0 00 20 32 00 01 0c DID 25 nn F7
26 F0 00 20 32 00 01 0c DID 26 nn F7
7D F0 00 20 32 00 01 0c DID 7D F7
Functions Note
Set device id (DID) n= DID to be set, range from [0-127], 0 ==any
Set midi channel nn = Midi TX channel number to be set, range from [0-16], 0 == Any channel.
mm = Midi RX channel number to be set, range from [0-16], 0 == Any channel.
Default value [1].
Set MIDI IN Transpose nn = transpose value [0-24]. Transpose range is -12 to + 12,
so 12 is no transpose. Default value [1].
Set velocity info nn = Key velocity of note on, 1 – 127 is a fixed value of velocity;
0 is dynamic velocity.
mm = Key velocity of note off, 1 – 127 is a fixed value of velocity;
0 is dynamic velocity.
pp = velocity Curve: 0 - soft, 1 - med, 2 - hard
Set pitch bend range nn = Pitch bend range [0-24] , 0 – 2 octave.
Ignore mm
Set key priority [0-low, 1- high, 2-last]
Set multi trigger nn = multi-trigger [0-off, 1-on].
Ignore mm
Set modulation curve. nn = curve [0-soft, 1-Med, 2-hard]
Set the Note @zero CV [0-127]
Set the MIDI clock output nn = [0—OFF, 1—DIN, 2—USB, 3-BOTH]
Set external clock polarity. nn = [0—FALLING, 1—RISSING],
Set sync clock rate nn = [0 – 1 PPS, 1 – 2 PPQ, 2 – 24 PPQ, 3- 48 PPQ]
Set sync clock source. nn = [0 – Internal, 1 – DIN, 2 – USB, 3 – TRIG]
Modulation wheel range nn = [0-4]
Set midi output of nn = [0—OFF, 1—DIN, 2—USB, 3-BOTH]
modulation wheel
Set midi output of nn = [0—OFF, 1—DIN, 2—USB, 3-BOTH]
pitch wheel
Set midi output nn = [0—OFF, 1—DIN, 2—USB, 3-BOTH]
of keyboard
Set midi output of nn = [0—OFF, 1—DIN, 2—USB, 3-BOTH]
keyboard after touch
Set midi output of nn = [0—OFF, 1—DIN, 2—USB, 3-BOTH]
sequencer
Set midi output of nn= [0—OFF, 1—DIN, 2—USB, 3-BOTH
arpeggiator
Restore factory settings
Default
[0]
[1]
[1]
nn = [0],
mm = [0],
pp = [0]
[12 -- 1 octave]
[2-last]
Nn = [nn=1, on]
[0- soft]
[0x24-C2]
[3-BOTH]
[1—RISING]
[2-24 PPQ]
[0 – Internal]
[2—100%]
[3-BOTH]
[3-BOTH]
[3-BOTH]
[3-BOTH]
[3-BOTH]
[3-BOTH]