Zoom 4411 Inicio Rápido

W I R E L E S S - N U S B A D A P T E R
Q U I C K S T A R T
This Quick Start is for quick installation of the USB adapter onto Windows 7, Vista, XP, or 2000 computers.
MAC users and others can also view the more comprehensive User Manual by inserting the adapter's CD into
their computer's CD or DVD drive and double-clicking on the User Manual to open the document. Then go to
the section that suits your needs.
To install the Adapter
Important: Do not plug the Adapter into your computer yet. We will tell you when to plug it in.
1
Insert the Wireless-N USB CD into the CD or DVD drive. The CD should start automatically.
For Windows Vista and Windows 7 only:
If the AutoPlay dialog box appears, click Run Setup.exe.
If a message appears saying An unidentified program wants access to your computer or Do you want
to allow the following program from an unknown publisher to make changes to this computer?, click
Allow or Yes.
2 On the next screen, select Install.
3
A Zoom Wireless-N USB Setup screen is displayed for a few seconds while the installation proceeds.
4
On the InstallShield Wizard Complete screen, click Finish and remove the CD.
5
Plug the USB Adapter into one of the available USB slots on your computer. (If it is difficult to insert the
USB Adapter directly into the USB slot because there isn't enough space near the slot, first plug the USB
Adapter into the extension cable included in the package and then plug the other end of the extension
cable into the USB slot in your computer. Since the extension cable is semi-rigid, you can twist the
extension cable to orient the USB Adapter for best reception. Usually a vertical orientation is best.)
To connect to a network
Now you are ready to connect to a network. Wireless networks typically have a wireless access point, router,
or gateway at the heart of the wireless network. Wireless networks sometimes use wireless security and
sometimes do not. What you do next depends on your network's wireless security. You have several options:
1
If your access point or router supports WPS, we highly recommend that you connect to a network using
WPS as described below.
2
If your access point does not support WPS or you prefer not to connect this way, you can connect to a
network without security as described below.
3
If you decide that you want to join a wireless network that has security without using WPS, please
refer to the User Manual by inserting the CD included in the package into the CD or DVD drive and
double-clicking on the User Manual to open the document. Then scroll down to Section 2: Setting
Security and follow the instructions.
To connect to a network using WPS
Your wireless access point, router, or gateway needs to support WPS. This typically means that the router has
a WPS button built into its case.
1
Start by double-clicking the Zoom icon on your desktop or taskbar to launch the Config Utility.
2
On the Configuration tab, click the WPS button to open the WPS Config screen.
3
Go to the access point (e.g. router) and activate the WPS pushbutton (or Secure Setup or similarly named
button, or a virtual pushbutton on the software display of the access point). You may have to hold down
the WPS button for several seconds or until the WiFi indicator light on the access point starts flashing.
The access point will now begin accepting WPS connections. (If security has not been set on the access
point, a random SSID and WPA key will be used.)
4
Now, click on PBC (Push Button configuration) on Zoom's WPS Config screen.
You should now have a secure connection. Open your Web browser and go to your favorite site.
To connect to a network without security
1
Double-click the Zoom icon on your desktop or taskbar to open the configuration software.
2
In the Zoom Wireless-N USB Network window, look through the list of available wireless networks and
highlight the network you want, and then click Connect.
3
If you join a wireless network that does not have security, you should now be connected. To check your
connection, open your Web browser and go to your favorite site.
Troubleshooting Tips
If your Zoom Wireless-N USB adapter is not working properly, try these steps:
• Make sure the adapter is not damaged and that it is securely connected to the computer, either directly or
through its short USB extension cable (which is included in the package).
•
Perform a power cycle – take the following steps in the order given:
1. Turn off the computer.
2. Turn off your wireless router, gateway or access point and wait a few seconds.
3. Turn the router, gateway or access point back on.
4. Turn on the computer.
Windows Vista users: Try again to connect your wireless adapter to a network using Windows
Networking.
•
If you are using the USB extension cable, try changing the orientation of the adapter by twisting the semi-
rigid USB extension cable to angle it toward the direction of the access point.
•
Try the adapter in another USB port.
• Unplug other USB devices from your computer one at a time and see if that allows the adapter to work.
• If possible, try installing the adapter on another computer.
If the problem does not seem to be hardware-related, click the Zoom icon on your desktop to run the Wireless-
N USB software.
1
Check the Configuration tab to make sure that the SSID and Network Type settings for the adapter are
the same as these settings for the other devices in your wireless network.
2
Then check the security settings to make sure that the adapter is configured for the same security system
as the other devices in your wireless network. Make sure that your security key is the same – remember
that the keys are case-sensitive.
3
Check your TCP/IP settings as discussed in Appendix A of the User Manual by inserting the CD included
in the package into the CD or DVD drive and double-clicking on the User Manual to open the document.
Then scroll down to Appendix A and follow the instructions.
4
If the adapter still does not work, uninstall the software and then re-install it. To do this, first go to the
notification area of the taskbar (commonly found on the bottom right corner of your desktop), right-click
and select the Safely Remove Hardware icon. Highlight USB Mass Storage Device and click Stop. In
the next screen, click OK. Then click OK again and then click Close to exit the window. Now, you can
physically remove the USB adapter from the USB port. Then select Start, All Programs, Zoom Wireless-
N USB, Uninstall Zoom Wireless-N USB. Now you can re-install the Wireless-N USB software by
following the instructions at the beginning of this Quick Start guide starting from
Getting Help
If you need assistance, please go to www.zoom.com and select Technical Support for help via our Web
SmartFacts system, email or phone.
FCC Regulations
This equipment has been tested and found to comply with the limits for a Class C digital device, pursuant to part 15 of the FCC Rules.
These limits are designed to provide reasonable protection against harmful interference in a residential installation. This equipment
generates, uses, and can radiate radio frequency energy and, if not installed and used in accordance with the instructions, may cause
harmful interference to radio communication. However, there is no guarantee that interference will not occur in a particular installation.
If this equipment does cause harmful interference to radio or television reception, which can be determined by turning the equipment
off and on, the user is encouraged to try to correct the interference by one or more of the following measures:
-Reorient or relocate the receiving antenna.
- Increase the separation between the equipment and receiver.
- Connect the equipment into an outlet on a circuit different from that to which the receiver is connected.
- Consult the dealer or an experienced radio/TV technician for help.
FCC Caution: Any changes or modifications not expressly approved by the party responsible for compliance could void the user's
authority to operate this equipment. This device complies with Part 15 of the FCC Rules. Operation is subject to the following two
conditions: (1) This device may not cause harmful interference, and (2) this device must accept any interference received, including
interference that may cause undesired operation.
NOTE: All Telecom and safety Tests only include this content hardware device only.
CE Declaration of Conformity
This equipment is intended to be used in all Europe and EFTA countries. Hereby Zoom Telephonics declares that this product is in
conformity with European R&TTE Directive (1999/5/EC).
RF Exposure Information (SAR)
FCC Radiation Exposure Statement:
This equipment complies with FCC radiation exposure limits set forth for an uncontrolled environment. This equipment should be
installed and operated with a minimum distance of about eight inches (20cm) between the radiator and your body. This transmitter
must not be co-located or operated in conjunction with any other antenna or transmitter.
Modular Approval Statement:
This device is intended to be used only for OEM integrator under the following conditions:
1) The antenna must be installed such that 20 cm is maintained between the antenna and users, and
2) The transmitter module may not be co-located with any other transmitter or antenna.
IMPORTANT NOTE:
In the event that these conditions cannot be met (for example certain laptop configurations or co-location with another transmitter),
then the FCC authorization is no longer considered valid and the FCC ID cannot be used on the final product. In these circumstances,
the OEM integrator will be responsible for re-evaluating the end product (including the transmitter) and obtaining a separate FCC
authorization.
.
To install the Adapter