After Use - Skil 0230 Manual Original

- after striking a foreign object
- whenever the tool starts vibrating abnormally
• Always ensure that the ventilation openings are kept
clear of debris

AFTER USE

Store the tool indoors in a dry and locked-up place, out
•
of reach of children
- store the battery pack separately from the tool
BATTERIES
• The battery supplied is partially charged (to ensure
full capacity of the battery, completely charge the battery
in the battery charger before using your power tool for the
• Only use the following batteries and chargers with
this tool
- SKIL battery: BR1*31****
- SKIL charger: CR1*31****
• Do not use the battery when damaged; it should be
replaced
• Do not disassemble the battery
• Do not expose tool/battery to rain
Permitted ambient temperature (tool/charger/battery):
•
- when charging 4...40°C
- during operation –20...+50°C
- during storage –20...+50°C
EXPLANATION OF SYMBOLS ON TOOL/BATTERY
3 Read the instruction manual before use
4
burn battery for any reason
5 Store tool/charger/battery in locations where temperature
will not exceed 50°C
6 Pay attention to the risk of injury caused by flying
debris (keep bystanders a safe distance away from work
area)
7 Wear protective glasses and hearing protection
8 Do not expose tool to rain
9 Do not dispose of electric tools and batteries together
with household waste material
USE
Assembly instructions
•
- mount cutting guard A as illustrated with 2 screws w a
! never use the tool without cutting guard A
-
- mount the guide handle B as illustrated r
• Charging battery
! read the safety warnings and instructions
provided with the charger
• Removing/installing the battery 2
•
e
-
-
! after switching off the tool the cutting line
continues to rotate for a few seconds
- allow the cutting line to stop rotating before switching
on again
! do not rapidly switch on and off
• Battery level indicator q
- press the battery level indicator button AA to show the
current battery level q a
! when the lowest level of the battery indicator
starts flashing after pressing button AA q b, the
battery is empty
w b
! when 2 levels of the battery indicator start flashing
after pressing button AA q c, the battery is not
within the allowable operating temperature range
• Battery protection
being switched on, when
- the load is too high --> remove load and restart
- the battery temperature is not within the allowable
operating temperature range of -20 to +50°C --> 2
pressing button AA q c; wait until battery has returned
within the allowable operating temperature range
- the battery is nearly empty (to protect against
deep discharge)
battery level q b is shown by the battery level indicator
when pressing button AA; charge battery
! do not continue to press the on/off switch after the
tool is switched off automatically; battery may be
damaged
• Setting the guide handle position r
- release guide handle adjustment knob C
- adjust guide handle position
- fasten guide handle adjustment knob C
• Setting the tube length t
• Setting the main handle orientation y
1. downwards for trimming
2. sidewards for edging
• Setting the pivot function u
- set tube angle according
1. free standing storage
2. trimming in narrow spaces
3. regular trimming
4. trimming under low objects
5. edging function
•
unintentional pruning
-
trimming near hard obstacles
-
• Setting up the tool for trimming
- set tube length D t
- set main handle orientation in trimming position y
- use pivot position 2, 3 or 4 u
-
• Setting up the tool for edging
- set tube length D t
- set main handle orientation in edging position y
- use pivot position 5 u
-
- for edging, support the tool by the edging wheel S p
• Trimming
! ensure that the cutting area is free of stones,
debris and other foreign objects
! start trimming only when tool runs at full speed
- cut long grass in layers (always start from the top)
- only trim with the tip of the cutting line
- do not cut damp or wet grass
- prevent the cut grass from clogging the spool (do not
make heavy cuts)
- do not overload the tool
- carefully cut around trees and bushes, so that they do
not come into contact with the cutting line
12
i
i
i