Important Safety Information; Safety Precautions - Titan SPEEFLO PowrLiner 2850 Manual Del Propietário

Important Safety Information

This symbol indicates a hazardous situation, which, if
not avoided could result in death or serious injury.
To reduce the risks of fire or explosion, electrical
shock, and the injury to persons, read and understand
all instructions included in this manual. Be familiar
with the controls and the proper usage of the
equipment.
WaRNING – To reduce the risk of fire or
explosion:
1. Do not spray flammable or combustible materials
near an open flame, pilot lights or sources of
ignition such as hot objects, cigarettes, motors,
electrical equipment and electrical appliances.
Avoid creating sparks from connecting and
disconnecting power cords.
2. For units intended for use with only water-based materials
— Do not spray or clean with flammable liquids. For use with
water-based liquids only.
3. For units intended for use with only water-based or mineral
spirit-type materials with a minimum flash point of 21ºC
(69.8ºF) — Do not spray or clean with liquids having a
flash point of less than 21ºC (69.8ºF). Flash point is the
temperature at which a fluid can produce enough vapor to
ignite.
4. Paint or solvent flowing through the equipment is able to result
in static electricity. Static electricity creates a risk of fire or
explosion in the presence of paint or solvent fumes. All parts
of the spray system, including the pump, hose assembly,
spray gun and objects in and around the spray area shall
be properly grounded to protect against static discharge
and sparks. Use only conductive or grounded high-pressure
airless paint sprayer hoses specified by the manufacturer.
5. Verify that all containers and collection systems are grounded
to prevent static discharge.
6. Connect to a grounded outlet and use grounded extension
cords (electric models only). Do not use a 3 to 2 adapter.
7. Do not use a paint or solvent containing halogenated
hydrocarbons. Such as chlorine, bleach mildewcide,
methylene chloride and trichloroethane. They are not
compatible with aluminum. Contact the coating supplier about
compatibility of material with aluminum.
8. Keep spray area well ventilated. Keep a good supply of fresh
air moving through the area to keep the air within the spray
area free from accumulation of flammable vapors. Keep
pump assembly in well ventilated area. Do not spray pump
assembly.
9. Do not smoke in the spray area.
10. Do not operate light switches, engines, or similar spark
producing products in the spray area.
11. Keep area clean and free of paint or solvent containers, rags,
and other flammable materials.
12. Know the contents of the paint and solvents being sprayed.
Read all Material Safety Data Sheets (MSDS) and container
labels provided with the paints and solvents. Follow the paint
and solvent manufacture's safety instructions.
13. Place pump at least 25 feet (7.62 meters) from the spray
object in a well ventilated area (add more hose if necessary).
Flammable vapors are often heavier than air. Floor area must
be extremely well ventilated. The pump contains arcing parts
that emit sparks and can ignite vapors.
14. Plastic can cause static sparks. Never hang plastic to
enclose spray area. Do not use plastic drop cloths when
spraying flammable material.
15. Fire extinguisher equipment shall be present and working.
English
operating the equipment. SavE ThESE INSTRucTIONS.
·
Read all safety information before
WaRNING – To reduce the risk of skin
injection:
haZaRD:
Injection injury – a high pressure fluid stream produced by this
equipment can pierce the skin and underlying tissues, leading
to a serious injury and possible amputation. See a physician
immediately. DO NOT TREaT aN INJEcTION aS a SIMPLE cuT.
1. Do not aim the gun at, or spray any person or animal.
2. Keep hands and other body parts away from the discharge.
For example, do not try to stop leaks with any part of the
body.
3. Always use the nozzle tip guard. Do not spray without the
nozzle tip guard in place.
4. Only use a nozzle tip specified by the manufacturer.
5. Use caution when cleaning and changing nozzle tips. In the
case where the nozzle tip clogs while spraying,
ALWAYS lock gun trigger, shut pump off, and release all
pressure before servicing, cleaning tip or guard, or changing
tip. Pressure will not be released by turning off the motor.
The PRIME/SPRAY valve or pressure bleed valve must
be turned to their appropriate positions to relieve system
pressure. Refer to PRESSURE RELIEF PROCEDURE
described in the pump manual.
6. Do not leave the unit energized or under pressure while
unattended. When the unit is not in use, turn off the unit and
relieve the pressure in accordance with the manufacturer's
instructions.
7. High-pressure spray is able to inject toxins into the body and
cause serious bodily injury. In the event that injection occurs,
seek medical attention immediately.
8. Check hoses and parts for signs of damage, a leak can inject
material into the skin. Inspect hose before each use. Replace
any damaged hoses or parts.
9. This system is capable of producing 3300 PSI / 22.8
MPa. Only use replacement parts or accessories that are
specified by the manufacturer and that are rated a minimum
of 3300 PSI. This includes spray tips, nozzle guards, guns,
extensions, fittings, and hose.
10. Always engage the trigger lock when not spraying. Verify the
trigger lock is functioning properly.
11. Verify that all connections are secure before operating the
unit.
12. Know how to stop the unit and bleed pressure quickly. Be
thoroughly familiar with the controls. Pressure will not be
released by turning off the motor. The PRIME/SPRAY valve
or pressure bleed valve must be turned to their appropriate
positions to relieve system pressure. Refer to PRESSURE
RELIEF PROCEDURE described in the pump manual.
13. Always remove the spray tip before flushing or cleaning the
system.
WaRNING – To reduce the risk of injury:
1. Always wear appropriate gloves, eye protection, clothing
and a respirator or mask when painting. Hazardous vapors
– Paints, solvents, insecticides, and other materials can be
harmful if inhaled or come in contact with body. Vapors can
cause severe nausea, fainting or poisoning.
2. Do not operate or spray near children. Keep children away
from equipment at all times.
3. Do not overreach or stand on an unstable support. Keep
effective footing and balance at all times.
4. Stay alert and watch what you are doing.
5. Do not operate the unit when fatigued or under the influence
of drugs or alcohol.
2 © Titan Tool Inc. All rights reserved.