Idiomas disponibles
  • ES

Idiomas disponibles

  • ESPAÑOL, página 16

Enlaces rápidos

®
PEAK
LC BOND
Light Cure Resin
Indications:
For use in most light-accessible bonding procedures.
Note: Peak
LC Bond Resin is the adhesive resin used when utilizing a total etch procedure with the
®
following materials:
1. Dentin and Enamel, Section I
2. Metals, Section II
3. Composite Repair, Section III
Procedure(s):
Remove luer lock caps from syringes and attach appropriate tips:
Ultra-Etch: Blue Micro tip (some prefer the Inspiral
Peak
LC Bond Resin: Inspiral
®
Section I. Dentin and Enamel
I. Prepare Tooth Surface: Prepared dentin and enamel surfaces to be bonded should be clean
and isolated. Surfaces should be caries free. For abrasion/abfraction Class V preparations,
roughen with a diamond bur. We recommend rubber dam where appropriate.
2. Etch: Apply Ultra-Etch onto preparation surfaces and leave for 15 seconds. Rinse dentin and
enamel thoroughly for 5 seconds with firm air/water spray. With brief air blasts, remove all visible
water. Leave dentin moist.
3. Bond: Immediately apply a uniform coat of Peak
an Inspiral
Brush tip. Brush gently for 10 seconds. Using air syringe, gently thin adhesive to a
®
uniform glossy coat and continue drying for 10 seconds. Avoid pooling of adhesive. Surface will
look glossy. Light cure for 20 seconds using a standard light with an output less than 1000mW.
Light cure 10 seconds using a light with an output greater than 1000mW.
Description:
Peak
LC Bond Resin is a syringe delivered single component resin
®
bonding system. Peak
either with the Peak
Etch, as treatment dictates. This light cure bonding agent is 7.5%
filled, radiopaque with an ethyl alcohol solvent carrier and will cure
with most curing lights including LEDs.
Brush tip
®
LC Bond Resin dental adhesive can be use
®
SE Primer or with a total etch, such as Ultra-
®
Brush tip)
®
LC Bond Resin onto etched tooth surface with
®
loading

Resumen de contenidos para Ultradent Products PEAK LC BOND

  • Página 16: Sección I: Dentina Y Esmalte

    Descripción: Resina Peak® LC Bond es un sistema adhesivo de resina, monocomponente, en jeringa. El adhesivo dental de Resina Peak® LC Bond puede utilizarse ya sea con Peak® SE Primer o con un grabador total como Ultra-Etch, según lo indique el tratamiento. Este agente adhesivo de fotocurado tiene 7,5% de carga, es radiopaco con un vehículo solvente de alcohol etílico y podrá...
  • Página 17: Sección Ii: Metal

    Composite: Se puede utilizar un composite fluido (por ej. PermaFlo®) como capa de adaptación inicial. Utilice composite de restauración para la última capa de 2-3 mm. Para superficies cuyo desgaste sea mínimo, como ser Clases V, puede utilizarse composite fluido como superficie final. Siga las instrucciones de uso del fabricante del composite.
  • Página 18 Adhesión: Aplique una capa uniforme de Resina Peak® LC Bond sobre la superficie grabada del diente con una punta Inspiral® Brush. Frote suavemente durante 10 segundos. Utilizando la jeringa de aire, afine suavemente el adhesivo hasta lograr una capa brillante y uniforme y continúe secando 10 segundos más.
  • Página 43 ® ® ® ® ® ®...
  • Página 44 ®...
  • Página 45 ®...
  • Página 52 ® ® ® ® ® ®...
  • Página 53 ®...
  • Página 54 ®...
  • Página 59 EN-Key: IT-Legenda: FI-Merkkien selitykset: EL-Kλειδί: KR-중요: DE-Legende: ES-Clave: FR-Explication : PT-Legenda: RU-Ключ: CH-主要注意事項: NL-Erklärung der SV-Teckenförklaring: PL-Legenda: Packungssymbole: DA-Tegnforklaring: TK-Anahtar: JA-重要 : PL-Środek drażniący EN-Irritant SV-Irriterande TK-Tahriş edici DE-Irritierend DA-Lokalirriterende EN-Refrigerate FR-Irritant FI-Ärsyttävä KR-자극성 제품 DE-Kühlen NL-Irriterend EL-Ερεθιστικό FR-Réfrigérer IT-Irritante RU-Обладает...