Connecting To The Mains; Assembly And Adjustments - DeWalt D28710 Traducido De Las Instrucciones Originales

When using a cable reel, always unwind the cable
completely.

Connecting to the Mains

The mains supply to be used for this machine must
be equipped with a 16 A cut-out fuse with time delay.
Voltage Drops
Inrush currents cause short-time voltage drops.
Under unfavourable power supply conditions, other
equipment may be affected.
If the system impedance of the power supply is lower
than 0.11 ø, disturbances are unlikely to occur.

ASSEMBLY AND ADJUSTMENTS

WARNING: To reduce the risk of
injury, turn unit off and disconnect
machine from power source before
installing and removing accessories,
before adjusting or changing set-ups
or when making repairs. Be sure the
trigger switch is in the OFF position. An
accidental start-up can cause injury.
Removing and Fitting a Cutting Disc
(fi g. 1, 2)
• With the arm in the rest position, use the lip (v)
to slide the guard (o) back. Leave the guard
retracted (fig. 2).
• Press and hold down the spindle lock (p) (fig. 1).
• Rotate the cutting disc (n) until it locks.
• Using the hex key (k), remove the bolt (w) by
turning counterclockwise and then remove the
flat washer (x) and the retaining flange (y) (fig. 2).
• Check that the spacer (z) is in place against the
flange (aa).
• Replace the cutting disc (n). Make sure that the
new disc is placed onto the spacer (z) in the
correct rotational direction.
• Secure the blade with the retaining flange (y), the
flat washer (x) and the bolt (w).
• Move the guard back down and release the
spindle lock (p).
• Adjust the cutting depth as necessary.
Adjusting the Cutting Depth (fi g. 1)
The cutting depth can be adjusted to meet the wear
of the cutting disc.
• Make a dry run with the tool switched off and
check for clearance.
• If adjustment is required, proceed as follows:
• Loosen the lock nut (f) a few turns.
• Turn the depth stop bolt (e) in or out as to
achieve the required cutting depth.
• Tighten the lock nut (f).
WARNING: Always adjust the depth stop
to its original position when replacing the
cutting disc.
Clamping the workpiece in position (fi g. 1, 3)
The tool is equipped with a material clamp (i) (fi g. 1).
• Pull the lever (m) toward the handle (l) (fi g. 3A).
• Push the clamp shaft (bb) forward until the jaw
(cc) is almost touching the workpiece.
• Press the lever (m) toward the jaw (cc) until it
engages with the clamp shaft (bb).
• Rotate the handle (l) clockwise and clamp the
workpiece securely.
• To release the workpiece, rotate the handle (l)
counterclockwise.
WARNING:
• To increase the cutting capacity, place a
spacer block (dd) under the workpiece
(ee). The spacer block should be slightly
narrower than the workpiece (fi g. 3B).
• Support long workpieces using a piece
of wood (ff) (fi g. 3C). Do not clamp the
cut off end (gg).
Quick Travel Feature (fi g. 3A)
The clamp has a quick travel feature.
• To release the clamp, rotate the handle (l) one or
two turns counterclockwise and pull the lever (m)
toward the handle (l).
Setting the Clamping Position (fi g. 3D)
The clamping position can be set to match the
cutting disc.
• Remove the fence bolts (hh) using the hex
key (k).
• Move the fence (h) as required.
• Re-fi t the fence bolts (hh) and tighten them to
lock the fence (h).
E N G L I S H
31