Worx WU621 Manual De Instrucciones página 9

OPERATING INSTRUCTIONS
1. SAFETY ON/OFF SWITCH
The switch is locked off to prevent accidental
starting. Depress the lock off button (2) then
on/off switch (1) and release lock off button (2).
The machine is working now.To switch off just
release the on/off switch (See A)
2. CUTTING DEPTH ADJUSTMENT
Smaller cutting depth of 0-1mm (Max. 2.0mm)
is best for most surface planing or rebating.
Rotate the cutting depth adjustment(4) to
set the required cutting depth on the scale
,Scale graduation = 0.125mm) .The clockwise
rotation increases the planing depth; the
counterclockwise rotation reduces the planing
depth. (See B)
Caustion: Do not rotate the
cutting depth adjustment in
counterclockwise too circles. It may
cause the front base plate fall off from
the machine.
3. ADJUST DUST EXTRACTION AND CHIP
EJECTION
Dust extraction can be adjusted to the right or
left side by manually. Rotating one end of the
dust extraction (5) until it stops (See C).The
arrowhead on the dust extraction indicates the
dust extraction direction.
Note: Due to the size and material
of some wood shavings e.g. wet or
hard wood it is possible for the dust
extraction to become blocked. Remove
the plug from the mains power supply,
then using a wooden stick clear the blocked
dust extraction.
4. BASEPLATE STAND
Uplift the rear of the planer, the baseplate
stand (6) can make the machine to be set
down directly and protect the cutting blades
from any damage and the blades from
damaging the surface(See D). When planing,
the stand will be pushed away by the end of
the wood. Always check the stand is free to
move on the base plate (See E).
5. BLADE FITTING AND CHANGING
Warning: Remove power cord from
the socket before carrying out any
adjustments or changing blades.
The blade has two cutting edges, which can
Planer
13L-WU621-M-070305¸ÄFÓïCE´¦.indd 9
be reversed .When replacing or reversing the
plane blades, the guide groove guarantees
constant height adjustment.
Note: Dull and worn blade cannot be reground
and must be replaced.
Remove the plug from the mains socket.
Using the Socket spanner (19) provided loosen
the 3 bolts approximately 1/2 rotation counter-
clockwise(See F .1).Holding the blade clamp (7)
in position, using a piece of wood slides the
blade (8) out of the blade clamp (7) to remove
the blade from the blade clamp(See F .2)Note:
there is no need to remove the blade clamp
(7) as this can change the factory settings for
cutting blade height control. Before reinserting
a new or reverse blade, always clean both
the blade and the blade seat if dirty. Slide
the blade into the blade clamp in the correct
orientation. Check the blade is equal with
the clamp. When tightening the screws(10)
ensure the correct tightening sequence( , ,
). Before starting, rotate by hand to check the
roller is free to rotate.
Rotate the blade head by a further 180
repeat the procedure disassembling the
second plane blade
6. REPLACING A DRIVE BELT
Warning: 1. Remove the plug from
the socket before carrying out any
adjustment, servicing or maintenance.
2. The cutting blades will be turning and
may cause injury.
Loosen screw and remove belt cover (11),
remove worn drive belt from large pulley (13)
and pinion (12) and clean them (See G).lace
the new drive belt on the top of pinion and
turning it manually, press it on the large pulley
(13) (See H).Make sure the drive belt runs
exactly along the length grooves of the pinion
and the pulley.
Note: Place the belt cover (11) back on
top and tighten it with screw.
7. FITTING A DUST BAG
This accessory can be fitted by sliding the dust
bag inlet over the planer dust extraction (5) as
far as possible.The dust bag will reduce the
efficiency of the exhaust system and the bag
must be emptied frequently to maintain the
efficiency.To empty, open the zip on the rear
of the dust bag.
Note: This accessory can be used for
smaller jobs.
and
o
09
ENG
3/5/2007 4:17:14 PM