Tabla de contenido
Idiomas disponibles
Idiomas disponibles
Pump
Maintenance
This mode[ does not require any pump maintenance.
The pump is predubricated and sealed, requiring no
additional lubrication for the life of the pump.
ENGINE MAINTENANCE
WARNING
WHEN
ADJUSTING
OR MAKING
REPAIRS
TO YOUR
PRESSURE
WASHER
Disconnect
the spark plug wire from the spark
plug and
place the wire where
it cannot
contact
spark plug.
WHEN
TESTBNG
FOR ENGINE
SPARK
Use approved
spark
plug tester.
DO NOT check
for spark with spark
plug removed,
OH
Oil Recommendations
NOTE: When adding oil to the engine crankcase, use
only high quality detergent oil rated with APi service
classification SF, SG, SH, SJ or higher. DO NOT use
special additives.
1.
Choose a viscosity according to the following tab[e:
3.
Verify oil is at "Fuji" mark on dipstick. Replace and
tighten dipstick.
/
Adding Engine Oil
1.
Make sure pressure washer is on a [eve[ surface.
2.
Check oil [eve[ as described in "Checking Oil Level".
3.
if needed, slowly pour oil into oil fi[J opening to the
"Fuir' mark on dipstick. DO NOT overfill
4.
Replace and tighten dipstick.
Changing Engine Oil
Change engine oil after the first 5 hours and every
50 hours thereafter, if you are using your pressure
washer under extremely dirty or dusty conditions, or in
extremely hot weather, change oil more often.
CAUTION
Used motor oil has been shown to cause skin cancer in
certain laboratory animals.
Thoroughly wash exposed areas with soap and water.
KEEP OUT OF REACH
OF CHILDREN.
DON'T
POLLUTE.
CONSERVE
RESOURCES.
RETURN
USED
OiL TO
COLLECTION
CENTERS.
STARTING
TEMPERATURE
RANGE
ANTICIPATED
BEFORE
NEXT
O;L CHANGE
NOTE: Synthetic oil meeting JLSAC GF-2, APJ
certification mark and API service symbol with "SJ/CF
ENERGY CONSERVING" or higher, is an acceptable
oil at all temperatures.
Use of synthetic oil does not
alter required oil change intervals.
* The use of multi-viscosity oils (5W-30, 10W-30, etc.)
in temperatures above 40°F (4°C) will result in higher
than normal oil consumption. When using a multi-
viscosity oil, check oil more frequently.
** If using SAE 30 oil in temperatures below 40°F
(4°C), it will result in hard starting and possible engine
bore damage due to inadequate lubrication.
Checking Oil Level
Oil [eve[ should be checked prior to each use or at [east
every 5 hours of operation. Keep oil [eve[ maintained.
1.
Make sure pressure washer is on a [eve[ surface.
2.
Remove oil dipstick and wipe dipstick with dean
cloth. Replace and tighten dipstick. Remove and
and check oil level
Change oil while engine is still warm from running, as
follows:
1.
Drain fuel tank by running pressure washer until
fuel tank is empty.
2.
Disconnect spark plug wire and keep it away from
spark plug.
3.
Clean area around oil fi[[, remove oil fi[J
cap/dipstick. Wipe dipstick clean.
4.
Tip your pressure washer to drain oil from oil ill[
into a suitable container making sure you tip your
unit away from spark plug. When crankcase is
empty, return pressure washer to upright position.
5.
Slowly pour recommended
oil (about 20 oz.) into
oil fiJ[opening. Pause to permit oil to settle. FiJ[to
"Fuji" mark on dipstick.
6.
Wipe dipstick dean each time oil [eve[ is checked.
DO NOT overfill
7.
Replace and tighten dipstick.
8.
Wipe up any remaining oil
9.
Reconnect spark plug wire to spark plug.
17
Tabla de contenido
