Use In The Vehicle - TAKATA I-SIZE BASE Manual De Instrucciones

it in position. The adjuster is positioned on the inner
side of the TAKATA I-SIZE BASE.
Step 2 – Adjust the ISOFIX connector
At the same time, pull the left-hand ISOFIX
connector, positioned on the outside of the TAKATA
I-SIZE BASE, into the required position.
Step 3 – Lock the ISOFIX length adjuster
Release the button and connector, and check whether
the latter is locked in place. This is indicated by a
click, and a green marking on the button.
NOTE!
The two ISOFIX connectors must be adjusted
independently. Repeat steps 1 to 3 for the right-hand
connector.
WARNING!
[I-SIZE_BASE_013] When securing the TAKATA
I-SIZE BASE in the vehicle, ensure that both ISOFIX
connectors are set to the same position. To do this,
FKHFN WKDW WKH ¿JXUHV RQ WKH WRS RI WKH FRQQHFWRUV
match up (or that both are blank). Failure to observe
this notice may seriously risk your child's safety, and
the safety of other passengers, in the event of an
accident.
Step 4 – Unlock the ISOFIX connectors
[I-SIZE_BASE_014] Unlock the left and right-hand
ISOFIX connectors, by taking hold of the release
sliders on each, moving the locking sliders of the
release sliders down and, at the same time, pulling the
release sliders towards the support leg. The connectors
have been correctly unlocked if you can see a red
marking on the top of each slider. If green markings
are shown, the connectors are still locked in place.
Releasing the rear connection hooks
[I-SIZE_BASE_015] The TAKATA MINI I-SIZE or
TAKATA MIDI I-SIZE is attached to the TAKATA
I-SIZE BASE via connection hooks at the front and
rear. To free the TAKATA MINI I-SIZE or TAKATA
MIDI I-SIZE from the TAKATA I-SIZE BASE, you
need only to release the rear hooks.
The rear hooks unlock together, so you only need to
push down one of the release elements on the exterior
of the connection arms. The connection hooks have
been correctly unlocked if you can see a red marking
on the top of each release element.
If green markings are shown, both, or in case of
partially green markings possibly only one of the
18
hooks are still locked in place. Please always also see
the warnings in the instructions for each seat:
TAKATA MINI I-SIZE – Section 5 – Use in the
vehicle (Securing the TAKATA MINI I-SIZE) or
TAKATA MIDI I-SIZE – Section 4 – Use in the
vehicle (Securing the TAKATA MIDI I-SIZE in a
backward-facing or forward-facing position).

4. USE IN THE VEHICLE

WARNING!
[I-SIZE_BASE_003] Never use the TAKATA I-SIZE
BASE on its own without the TAKATA MINI I-SIZE
or the TAKATA MIDI I-SIZE, or without properly
securing the TAKATA MIDI I-SIZE. Failure to
observe this notice may seriously risk your child's
safety, and the safety of other passengers.
NOTE!
Long-term use of the TAKATA I-SIZE BASE and
TAKATA MINI I-SIZE or TAKATA MIDI I-SIZE may
result in wear and tear of the vehicle seat.
Securing the TAKATA I-SIZE BASE
Step 1 – Fold out the support leg
Fold out the support leg as explained in Section 3 –
Basic instructions (Adjusting the support leg), and
ensure that it is properly locked in place.
NOTE!
Check the support leg is locked in place by lightly
shaking it with your hand.
Step 2 – Place on the vehicle seat
[I-SIZE_BASE_016] Place the TAKATA I-SIZE
BASE on the seat of the vehicle. Ensure that:
‡ WKH ,62),; FRQQHFWRUV DUH SRLQWLQJ WR WKH EDFN RI
the car seat.
‡ WKH VXSSRUW OHJ LV SRLQWLQJ WR WKH YHKLFOH ÀRRU
Step 3 – Pull out the ISOFIX connectors
[I-SIZE_BASE_012] Press in the button on the inner
side of each rear connection arm as far as possible,
and fully extend the connectors. Follow the instruction
in Section 3 – Basic instructions (Adjusting the
ISOFIX connectors).
NOTE!
The connectors have been fully extended when no
¿JXUH LV GLVSOD\HG RQ WKH WRS RI WKH ,62),;
connectors.