Before Starting The Equipment - EINHELL TC-CD 18-2 Li-i Manual De Instrucciones Original

5. Before starting the equipment

Be sure to read the following information before
you use your cordless screwdriver for the fi rst
time:
1. Charge the battery pack with the charger
supplied. An empty battery pack requires a
charging period of approximately 1 hour.
2. Only ever use sharp drill bits and screwdriver
bits which are suitable for the purpose and in
faultless condition.
3. Always check for concealed electric cables
and gas and water pipes when drilling and
screwing in walls.
6. Operation
6.1 Charging the Li battery pack (Fig. 2-3)
1. Remove the battery pack (5) from the handle,
pressing the pushlock button (8) downwards
to do so.
2. Check that your mains voltage is the same as
that marked on the rating plate.
3. Plug the power cable (a) of the charger (6)
into the power socket. The red LED (b) on the
charger will begin to shine. Push the battery
(5) onto the charger (6).
The 3 LEDs on the battery capacity indicator
(2) indicate that the battery is being charged.
- Battery is discharged: All 3 LEDs blink in
alternation
- 1/3 charged: the right-hand LED is lit, the
middle and left-hand LED blink in alternation
(looking at the bottom side of the battery)
- 2/3 charged: the right-hand and middle LED
are lit, the left-hand LED blinks (looking at the
bottom side of the battery)
4. When the charging operation ends after ap-
prox. 1 h, all 3 LEDs will will be lit for approx.
10 min. Remove the battery from the charger.
5. If all 3 LEDs blink simultaneously, this indica-
tes that the battery temperature is too low or
too high. Remove the battery from the char-
ger, keep it at room temperature for one day
and try again.
6. If the same fault is indicated again, the bat-
tery pack is defective. Never use or charge
a defective battery. Remove the battery from
the charger.
If the battery pack fails to become charged, ple-
ase check
•
whether there is voltage at the socket-outlet
GB
•
If the battery still fails to become charged, please
return
•
•
to our Customer Service Department.
To ensure that the LI battery pack provides
long service you should take care to recharge
it promptly. You must recharge the battery pack
when you notice that the power of the cordless
screwdriver drops.
6.2 Torque setting (Fig. 4 / Item 1)
Important! The tool must be at a standstill
when you set the torque with the setting ring.
The cordless screwdriver is fi tted with a mechani-
cal torque selector.
The torque for a specifi c size of screw is selected
with the set-collar (1). The correct torque depends
on several factors:
•
•
•
The clutch disengages with a grating sound to
indicate when the set torque is reached.
6.3 Selector switch for driving/drilling/impact
•
•
•
Important! Change the torque setting (1) and
the selector switch for driving/drilling/impact
drilling (11) only when the equipment is at a
standstill.
- 17 -
www.sidirika-nikolaidi.gr
whether there is proper contact at the char-
ging contacts on the charger.
the charger
the battery pack
on the type and hardness of material in ques-
tion
on the type and length screws used
on the requirements needing to be met by the
screwed joint.
drilling (Fig. 4 / Item 11)
For driving purposes, set the selector switch
(11) to the „Screw" position in the middle.
The torque will be adjusted according to the
torque setting (1) (see point 6.2).
For drilling purposes, set the selector switch
(11) to the „Drill bit" position on the right. The
slip coupling is now off and the maximum
torque is available depending on the torque
setting (1).
For impact drilling purpose, set the selector
switch (11) to the setting „Hammer" position
on the left. The slip coupling is now off and
the maximum torque is available depending
on the torque setting (1).