Saeco Nina Serie Instrucciones De Uso página 18

8 STEAM / CAPPUCCINO
Danger of scalding! When brewing starts, spurts
of hot water may come out. The spout can reach
high temperatures: do not touch it with bare hands.
• (Fig.3) - Press the ON/OFF button (2).
• Wait until the "machine ready" (15) light turns on.
• (Fig.19) - Switch the selection knob (17) to the " "
position.
• Wait until the light (16) turns on. The machine is now ready
for steam ejection.
• (Fig.18) - Place a container under the steam spout.
• (Fig.5) - Open the knob (4) for a few seconds, so that
remaining water fl ows out of the steam spout (Pannarello).
In a short time only steam will come out.
• Close the knob (4) and remove the container.
• Fill 1/3 of the container you wish to use to prepare your
cappuccino with cold milk.
Use cold milk to get a better result.
• (Fig.20) - Immerse the steam spout in the milk and open
the knob (4) by turning it anticlockwise. Turn the milk
container with slow upward movements so that it warms
up evenly.
A maximum steam brewing of 60 seconds is
recommended.
• When brewing ends, close the knob (4) and remove the
cup with the frothed milk.
• (Fig.19) - Switch the selection knob (17) to the "
position.
If both lights are on and the machine has reached a too
high temperature to brew coffee, prime the circuit as
described in section 4.5 to make the machine ready for
use.
Note: The machine is ready when the "machine
ready" light (15) is permanently on.
Note: If brewing a cappuccino as described is
not possible, prime the circuit as explained in
Section.5, then repeat the procedure.
The same procedure can be used to heat other
beverages.
• After this operation, clean the steam spout with a wet
cloth.
• 18 •
9 CLEANING
Maintenance and cleaning may only be carried out
when the machine has cooled down and has been
disconnected from the power supply.
• Do not immerse the machine in water nor place any of its
parts in a dishwasher.
• Do not use spirit, solvents and/or aggressive chemical
agents.
• We recommend cleaning the water tank and fi lling it up
with fresh water daily.
• (Fig.21-22) - Every day, after heating the milk, remove
the external part of the Pannarello and wash it with fresh
drinking water.
• (Fig.23) - Clean the steam spout weekly. In order to do
this, please:
- Remove the external part of the Pannarello (for standard
cleaning).
- Loosen the ring nut (without removing it).
- Remove the upper part of the Pannarello from the steam
spout.
- Wash the upper part of the Pannarello with fresh drinking
water.
- Wash the steam spout with a wet cloth and remove any
milk residue.
- Replace the upper part of the steam spout (make sure
it is completely inserted).
- Tighten the previously loosened ring nut.
Reassemble the external part of the Pannarello.
• (Fig.24) - Empty and clean the drip tray daily
• Use a damp and soft cloth to clean the appliance.
• (Fig.17) - Perform the following operations to clean the
pressurized fi lter holder:
"
- Remove the fi lter, wash it thoroughly with hot water.
- Remove the pin, wash it thoroughly with hot water.
- Wash the internal part of the pressurized fi lter holder.
• Do not dry the machine and/or its components in a
microwave and/or in a conventional oven.
Note: do not wash the pressurized portafi lter in
the dishwasher.
10 DESCALING
The formation of limescale inside the appliance is
inevitable. It is necessary to descale the machine every
1-2 months of use and/or when you notice a reduction in
the water delivery.
Please use Saeco descaling solution in your
machine (Fig.B). It has been specifically
developed to preserve performance and functionality
throughout the lifetime of the machine and to ensure,
with regular use, a high quality delivered product.
Warning! Do not use vinegar as a descaling
solution.