Troubleshooting Guide - Good Earth Lighting FP1246-WHG-17LFC-G Guia De Inicio Rapido

Panel de luces led plano con iluminación en los bordes

Tabla de contenido

WOOD

BBx2

Wood: Locate the open holes for mounting at the corners of the mounting plate and drill 1/8 in. pilot hole in the center. If a wooden stud is encountered, use

the wood screws (BB) provided to secure the mounting plate directly to stud.

To make installation easier, a pre-attached support wire is located on the back of the fixture. Attach the hook end through the center hole of the mounting

bracket to suspend the fixture in place while the wire connections are made.

Fixture must be properly grounded. Ground wires are usually either green or bare copper. Connect the fixture ground wire to the ground wire from the J-box

using a wire nut (DD). Connect the black supply lead (HOT) to the black fixture wire; and the white supply lead (NEUTRAL) to the white fixture wire using

wire nuts (DD). Secure the wire nuts properly to prevent the wires from coming loose. Push excess wire back into the J-box.

Leave the support wire attached to the mounting bracket. Lift the fixture up to the J-box to engage it with the mounting bracket. Align the mounting slots on the

back of the fixture with the metal tabs on the mounting bracket. Once the tabs are fully inserted into the slots, rotate the fixture counter- clockwise until the tabs

click and lock into place and the fixture is secure.

Slowly remove hands from the fixture. In the event the fixture was not installed properly, it will hang down. Slowly let the fixture down and try installing

again. This should prevent the wire connections from being pulled apart.

Restore power to the J-Box.

CARE AND MAINTENANCE

Periodically clean the fixture and diffuser using a mild, non-abrasive cleaner and soft cloth. When cleaning the fixture, make sure the power

is turned off. Do not spray cleaner directly onto any part of the fixture or LEDs.

Good Earth Lighting

The manufacturer warrants this lighting fixture to be free from defects in materials and workmanship for a period of (10) years from the date

of original purchase by the consumer. The fixture is not warrantied for use in a commercial or retail application. The warranty is limited to

use in a residential environment. We will repair or replace (at our option) the unit in the original color and style if available, or in a similar

color and style if the original item has been discontinued, without charge. Defective units must be properly packed and returned to the

manufacturer with a letter of explanation and your original purchase receipt showing date of purchase. Call 1-800-291-8838 to obtain a

return authorization number and an address where to ship your defective product. Note: C.O.D. shipments will NOT be accepted. The

liability of the manufacturer is in any case limited to replacement of the defective light fixture product. The manufacturer will not be liable for

any other loss, damage, labor costs or injury which is caused by the product. This limitation upon the liability of the manufacturer includes

any loss, damage, labor costs or injury which is (I) to person or property or otherwise; (II) incidental or consequential in nature; (III) based

upon theories of warranty, contract, negligence, strict liability, tort, or otherwise; or (IV) directly, or indirectly related to the sale, use, or

repair of the product. This warranty gives you specific rights, and you may also have other rights which vary from state to state.

FCC STATEMENT:

This device complies with Part 15 of the FCC rules. Operation is subject to the following two conditions: (1) This device may not cause harmful interference,

and (2) this device must accept any interference received, including interference that may cause undesired operation. Warning: Changes or modifications to

this unit not expressly approved by the party responsible for compliance could void the user's authority to operate the equipment. Note: This equipment has

been tested and found to comply with the limits for a Class B digital device, pursuant to Part 15 of the FCC rules. These limits are designed to provide

reasonable protection against harmful interference in a residential installation. This equipment generates, uses and can radiate radio frequency energy and,

if not installed and used in accordance with the instructions, may cause harmful interference to radio communications. However, there is no guarantee that

the interference will not occur in a particular installation. If this equipment does cause harmful interference to radio or television reception, which can be

determined by turning the equipment off and on, the user is encouraged to try to correct the interference by one or more of the following measures: 1)

Reorient or relocate the receiving antenna. 2) Increase the separation between the equipment and receiver. 3) Connect the equipment into an outlet on a

circuit different from that of the receiver. 4) Consult the dealer or an experienced radio/TV technician for help.