Tabla de contenido
20. Do not remove the pulp while the appliance is in operation.
21. When the appliance is in operation, do not put you hands or any objects into the feed
hole. To do this, use only the pusher (1.1).
22. Put fruit into the feed hole when the appliance is in operation. The feed hole must not
be filled with fruit or vegetables during a standstill.
23. Be careful not to overload the juice extractor. Do not use too much force when pushing
the products through the feed hole (1.2).
24. When the appliance is not used or when you want to clean it, always disconnect it from
the mains.
25. Do not dismantle the juice extractor if it is connected to a power socket.
26. Open the safety lock only after you have turned off the appliance and the filter has
stopped.
27. Do not use abrasive cleaning sponges or caustic cleaning agents to clean the
appliance.
28. Never immerse the engine unit in water or any other liquid.
29. The appliance may not be operated for more than 3 minutes without interruption. After
three minutes of operation, wait 30 minutes.
30. When extracting thick juices, do not operate the appliance for more than 1 minute.
DESCRIPTION OF THE DEVICE (Fig.1)
1. Pusher
3. Grater and filter basket
5. Juice outlet funnel
7. Safety locking handle
9. Body of the appliance
11. Blender jug
13. Blender cap
BEFORE THE FIRST USE
1. Unpack all elements and wash those parts of the appliance that will be in direct contact with fruit and juice with the use of warm water
with washing liquid. Then thoroughly rinse and dry the washed elements.
ASSEMBLING THE BLENDER (Fig. 2)
1. Place the body of the appliance (1.9) on a flat and stable surface. Then ensure that the speed control knob (1.8) is set to the "0"
position.
2. Place the blender jug (1.11) centrally on the body so that the rotor axis fits into the clutch located on the body.
3. Attach the jug (1.11) to the body (1.9) using safety locking handles (1.7). If the handles have been
installed properly, they can be snapped at the bottom after the jug is installed.
4. Place the ingredients intended for blending in the blender jug and cover the blender with the lid (1.12).
NOTE: Do not pour hot liquids into the blender. It is recommended that you use the "PULSE" function if you pour in ice cubes.
5. Never open the lid during blending. To add ingredients for blending, use the small hole in the lid (1.12).
ASSEMBLING THE JUICE EXTRACTOR (Fig. 3)
1. Place the body of the appliance (1.9) on a flat and stable surface. Then ensure that the speed control knob (1.8) is set to the "0"
position.
2. Place the juice and pulp separating bowl (1.4) on the body (1.9). Then install the grater and filter basket (1.3) and the lid (1.2) and
secure with the safety locking handle (1.7).
3. Install the pulp container (1.6) properly and place the juice jug (1.10) opposite, right under the funnel (1.5).
4. Wash the fruit or vegetables that you want to use. If they do not fit into the feed hole, cut them into smaller pieces.
5. Insert the plug into the socket and turn on the appliance by setting the switch to position '1' or '2'. Change the speed with the switch
(1.8) to low (switch in position "1") or high (switch in position '2'), depending on the fruit or vegetables used.
6. With the engine on, put the fruit (or vegetables) into the feed hole. Push them down using the pusher (1.1). To extract the maximum
amount of juice, push the fruit down slowly.
7. Juice will start to flow into the jug and the fruit pulp will start to accumulate in the container on the other side. To empty the pulp
container, turn off the juice extractor. Do not empty the container when the appliance is on or allow it to overfill, as this may damage
to the appliance.
CLEANING AND MAINTENANCE
1. For easier cleaning, rinse removable parts under running water immediately after every use. After you have rinsed them, leave the
elements to dry.
NOTE: Disconnect the plug from the socket before dismantling the elements.
2. After dismantling, all removable parts can be cleaned in warm water with dishwashing liquid.
3. The lid (1.2), the pulp container (1.6), the grater and filter basket (1.3) and the juice jug can be washed in a dishwashing machine.
NOTE: Do not wash the blender jug in a dishwashing machine or in hot water.
4. Wipe the body, which contains the engine of the juice extractor, with a soft cloth.
5. Do not immerse the grater and filter basket (1.3) in bleaching preparations.
2. Juice extractor cover
4. Juice and pulp separating bowl
6. Pulp container
8. On/Off switch
10. Juice container
12. Blender lid
4
Tabla de contenido
