Preparation For Operation - GRAPHITE 59G800 Instrucciones De Uso

Cutting depth gauge
9.
Cutting depth gauge adjustment screw
10.
Guide locking knob
11.
Guide
12.
Head locking lever
13.
Fence
14.
Fixing hole
15.
Angular scale of work table
16.
Work table angle marker
17.
Lever for automated position fixing
18.
Work table locking knob
19.
Table insert
20.
Work table
21.
Laser module cover
22.
Laser unit
23.
Fixed shield
24.
Dust extraction outlet
25.
Dust bag
26.
Vertical clamp fixing knob
27.
Vertical clamp arm
28.
Vertical clamp arm locking knob
29.
Work piece fixing knob
30.
Angular scale of head tilt
31.
Marker of head tilt position
32.
Battery compartment
33.
Laser switch button
34.
Laser
35.
Laser module fixing screws
36.
Central plate fixing screw
37.
Central plate
38.
Adjustment knob for angle 0
39.
Adjustment knob for angle 45
40.
* Differences may appear between the product and drawing
MEANING OF SYMBOLS
CAUTION
WARNING
ASSEMBLY / SETTINGS
INFORMATION
EQUIPMENT AND ACCESSORIES
Dust bag - 1 pce
1.
Special key - 1 pce
2.
Vertical clamp - 1 pce
3.

PREPARATION FOR OPERATION

Ensure the mitre saw is disconnected from power supply before
starting any installation or adjustment.
CARRYING THE MITRE SAW
• Make sure the head is locked in the lowest position when carrying
the mitre saw.
• Make sure that work table locking knob, head locking lever, and
other safety parts are tightened firmly.
INSTALLATION OF MITRE SAW ON A WORKBENCH
It is recommended to fix the mitre saw to a workbench or a stand
with the use of fixing holes (15) designed for such purpose. They
are located on the mitre saw base and guarantee safe operation
and eliminate risk of unwanted machine shifts during operation.
The holes allow to use coach bolts or bolts with hexagonal head and
8 mm in diameter.
When fixing the mitre saw to a workbench ensure that:
• Workbench top surface is flat and clean.
• Bolts are tightened equally and with moderate force (fixing bolts
0
0
must be tightened so the base is not under stress or deformed). In
case of over-stress there is danger of cracking the base.
DUST EXTRACTION
To prevent dust deposition and provide maximum working
efficiency, you can connect the mitre saw and industrial vacuum
cleaner using the dust extraction outlet (25). Alternatively, you can
collect the dust in the dust-bag (included) after installing it onto
dust extraction outlet. To install, press on the spring clamp and
put the dust bag (26) onto the dust extraction outlet (25) (fig. A).
To empty the dust bag, press on the spring clamp of the dust bag,
remove it from the dust extraction outlet and open the zip-fastener
that allows to access inside the bag.
To achieve optimal dust extraction empty the bag when it is 2/3
full.
USING THE SAW ARM (HEAD)
There are two positions of the saw arm, upper and lower. To release
the saw arm from locked lower position, do as follows:
• Press and hold down the arm.
• Pull the head locking pin (8) out.
• Hold the saw arm as it lifts to its upper position.
To lock the saw arm in lower position, do as follows:
• Press and hold the cutting blade guard lever (4).
• Press down the saw arm until it reaches its lower position.
• Lock the extension arm in this position by pressing the head
locking pin (8) in.
VERTICAL CLAMP
Vertical pressure clamp (fig. B) can be installed in the saw base at
either side of the work table and is fully adjustable to size of the
object to be cut. Do not use the saw without using vertical pressure
clamp.
• Loosen the vertical clamp fixing knob (27) at the base, on the side
where you plan to install the vertical clamp.
• To install the vertical clamp, slide it into the hole in the mitre saw
base, next tighten the vertical clamp fixing knob (27) to the saw
base.
• Once the vertical clamp arm (28) position is adjusted to work
piece, tighten the vertical clamp arm locking knob (29).
• Tighten the work piece fixing knob (30) so the work piece is
pressed against the work table (21).
• Make sure the work piece is secured.
OPERATION / SETTINGS
Ensure the saw is disconnected from power supply network before
starting any adjustment. To ensure safe, precise and efficient saw
operation, proceed with all adjustment procedures as a whole.
After finishing all the setting and adjustment procedures ensure
that all keys are collected. Check that all threaded joining
elements are properly tightened.
When making adjustments ensure that all external parts work
properly and are in good condition. Any worn out or damaged
part must be replaced by qualified personnel before starting to
use the saw.
SWITCHING ON / SWITCHING OFF
The mains voltage must match the voltage on the rating plate
of the saw.
Switch on the saw only when cutting blade is away from the
material that is to be cut.
Switching on
• Press and hold the switch button (3).
Switching off
• Release pressure on the switch button (3).
USING THE CUTTING DEPTH GAUGE
Cutting depth gauge is used for making key grooves in a work
13