Preparation For Operation - GRAPHITE 58G491 Traducción Del Manual Original

Safe work and maintenance
• Match cutting blade with material that you plan to cut.
• Never use the saw for cutting materials other than wood and
wood-like.
• Do not use the saw without guard or when the guard is blocked.
• Floor close to the machine work place must be kept tidy and
without loose materials and protrusions.
• Provide appropriate work place illumination.
• Machine operator must be properly trained for use, operation and
working with the machine.
• Use only sharp cutting blades.
• Observe maximum speed indicated on the cutting blade.
• Make sure to use parts in accordance with the manufacturer's
instructions.
• Disconnect the saw from power supply when performing
maintenance tasks.
• If the power cord gets damaged during operation, disconnect the
power supply immediately. DO NOT TOUCH POWER CORD BEFORE
DISCONNECTING FROM THE POWER SUPPLY.
• If the saw is equipped with laser, replacement with laser of
another type is forbidden and all repairs must be carried out by
Do not use the tool in stationary mode. It is not designed for use
with sawing table.
• Fix processed material to stable surface and secure with clamps or
vice to eliminate shifting. This kind of work piece fixation is safer
than holding the work piece in hand.
• Wait until blade comes to a complete stop before putting the
power tool away. Cutting blade may jam and cause loss of control
over the power tool.
CAUTION! This device is designed to operate indoors.
The design is assumed to be safe, protection measures and
additional safety systems are used, nevertheless there is always a
small risk of injuries at work.
Explanation of used symbols
1 2
6 7
Read instruction manual, observe warnings and safety
1.
conditions therein.
Device with class II insulation.
2.
Use personal protection measures (protective goggles, earmuff
3.
protectors, anti-dust mask)
Disconnect the power cord before starting maintenance or
4.
repair.
Protect against rain.
5.
Keep the tool away from children.
6.
Do not put your hands or legs close to cutting parts!
7.
Danger of kickback.
8.
Caution, risk of hand injuries and cutting fingers.
9.
CONSTRUCTION AND USE
Circular saw is a hand-held power tool with insulation class II. It is
driven by a single-phase commutator motor. Power tools of this
type are widely used for cutting wood and wood-based materials.
Do not use the saw for cutting firewood. Attempts to use the saw for
purposes other than specified will be considered an improper use.
Use the circular saw only with appropriate cutting blades with teeth
with sintered carbide tips. Circular saw is designed for light duty
works in service workshops and any individual, amateur activities
(tinkering).
3 4 5
8 9
Use the power tool in accordance with the manufacturer's
instructions only.
DESCRIPTION OF DRAWING PAGES
Below enumeration refers to the device elements depicted on the
drawing pages of this manual.
Dust extraction outlet
1.
Upper guard
2.
Voltage indicator
3.
Lower guard lever
4.
Knob for base bevel adjustment
5.
Edge guide locking knob
6.
Cutting line indicator for 45°
7.
Cutting line indicator for 0°
8.
Base
9.
Cutting blade
10.
Flange washer
11.
Fixing bolt for cutting blade
12.
Lower guard
13.
Front handle
14.
Switch
15.
Switch lock button
16.
Main handle
17.
Cutting depth locking lever
18.
Spindle lock button
19.
. Carbon brush cover
20
Edge guide
23.
* Differences may appear between the product and drawing.
MEANING OF SYMBOLS
CAUTION
WARNING
ASSEMBLY / SETTINGS
INFORMATION
EQUIPMENT AND ACCESSORIES
Edge guide
1.
Hexagonal key
2.

PREPARATION FOR OPERATION

CUTTING DEPTH ADJUSTMENT
Cutting depth for right angle can be set from the range of 0 to 55 mm.
• Loosen the cutting depth locking lever (18).
• Set desired cutting depth (use the scale).
• Lock the cutting depth locking lever (18) (fig. A).
INSTALLATION OF THE EDGE GUIDE
Use the edge guide when cutting material to narrow pieces. Guide
can be installed on either left or right side of the power tool.
• Loosen the parallel guide locking knob (6).
• Insert the edge guide bar (23) into two holes in the saw base (9).
• Set desired distance (use the scale).
• Use the edge guide locking knob (6) to fix the edge guide (23)
(fig. B).
The edge guide (23) can also be used for bevel cutting at angles
ranging from 0° to 45°.
Never put hand or fingers behind the working saw. When kick
back happens the saw can fall on the hand, it may be the cause
of heavy body injury.
MOVING THE LOWER GUARD
Lower guard (13) of the cutting blade (10) is pushed away
automatically as the blade sinks into the material. To remove it
manually push the lower guard lever (4).
DUST EXTRACTION
Circular saw is equipped with dust extraction outlet (1) that allows
for extraction of sawdust produced when cutting.
12
- 1 pce
- 1 pce