Stanley SXVC20TPE Manual Del Usuario página 11

4 GENERAL INFORMATION (PAGE 3)
4.1 Use of the manual
This manual forms an integral part of the appliance and should be kept
for future reference. Please read it carefully before installing/using the
unit. If the appliance is sold, the seller must pass on this manual to the
new owner along with the appliance.
4.2 Delivery
The appliance is delivered partially assembled in a cardboard box.
The supply package is illustrated in fig.1.
4.2.1 Documentation supplied with the appliance
D1 Use and maintenance manual
D2 Safety instructions
D3 Declaration of conformity
D4 Warranty regulations
4.3 Disposing of packaging
The packaging materials are not environmental pollutants but must still
be recycled or disposed of in compliance with the relevant legislation
in the country of use.
5 TECHNICAL INFORMATION (PAGE 3)
5.1 Envisaged use
The appliance is intended for use as an ash vacuum cleaner, in
compliance with the descriptions and safety precautions contained in
these instructions.
This appliance is designed for household use only and must not be
utilised for industrial or commercial purposes.
The appliance conforms to the IEC 60335-1 and IEC 60335-2-2
standards.
5.2 Operator
The symbol shown in fig. 1 identifies the appliance's intended
operator (professional or non-professional)
5.3 Main components:
A1 Starter device
A2 Suction union
A4 Handle
A5 Power cable stowing hook (where featured)
A6 Catches
A7 Power cable with plug
A9 Tank
A10 Cover with motor
A13 Filter shaker manual
5.3.1 Accessories (see fig. 1 for details of models - supply
package is as shown on the cardboard box)
B1 Filter holder with Cartridge
filter
B2 Fire retardant filter
B3 Hose
5.4 Safety devices
- Starter device (A1)
The starter device prevents accidental use of the appliance.
EN © 2017 English
B5 Tube
6 INSTALLATION (PAGE 4)
Warning - danger!
All installation and assembly operations must be performed with the appliance
disconnected from the mains power supply.
The assembly sequence is illustrated on page 4.
6.1 Assembly
When unpacking, check for any missing accessories or damage to the
contents. If damage caused in transit is found, notify your dealer at
once.
Lift the cover with the motor (A10) off the appliance, releasing the
catches (A6) and take out the accessories supplied, checking that the
filter (B1) and the filter (B2) are fitted correctly.
If filter (B2) has not been fitted, fit it so that it covers filter (B1)
completely.
See fig. 2
The assembly sequence is illustrated on page 4.
6.2 Fitting the accessories
Connect the hose (B3) to the intake (A2).
See fig. 3
Then complete the sequence by connecting the hose (B3) to the
tube (B5).
See fig. 4
6.3 Electrical connection
Warning - danger!
Check that the electricity supply voltage and frequency (V/Hz)
correspond to those specified on the data plate See fig.5
6.3.1 Use of extension cables
Use cables and plugs with "IPX4" protection level.
The cross-section of the extension cable should be
proportionate to its length; the longer it is, the greater its
cross-section should be.
7 INFORMATION ON USE OF THE APPLIANCE (PAGE 5)
7.1 Controls
- Starter device (A1). See fig. 6.
Set the starter device switch on (ON/I).
If there is a pilot light on the starter device, it should light up.
Set the starter device switch on (OFF/0) to stop the appliance.
If there is a pilot light on the starter device, it should go out.
Warning - danger!
During operation the appliance must be positioned as shown on a firm,
stable surface. See fig. 6.
7.2 Start-up
7.2.1 Suction. See fig. 7.
Only work with filter (B1) and filter (B2) dry!
Before use, check the filter (B1) and filter (B2) for damage
and replace them if necessary. Connect the relevant
accessory before sucking in cold ash. See fig. 7.
When sucking in ash, hold the nozzle (B5) at least 1 cm
above the surface of the material. See fig. 8.
11 (Original instructions)