Tabla de contenido
Idiomas disponibles
Idiomas disponibles
SPECIFIC SAFETY RULES
•
When using flashlights or lanterns,
WARNING
additional precautions should always
be followed, including the following:
a) To reduce the risk of injury, close supervision is
necessary when a product is used near children.
b) Do not contact hot parts.
c) Only use attachments recommended or sold by
the manufacturer.
•
The lens may get hot during use. To
WARNING
reduce the risk of burns, do not touch
hot lens.
•
To reduce the risk of injury, keep
WARNING
hands clear of the moving parts when
deploying legs and/or raising/lowering the mast.
•
To reduce the risk of injury, do not
WARNING
look directly into the light when the
light is on.
•
To reduce the risk of injury, ensure
WARNING
the light is stable before raising the
mast. Light may tip and cause injury.
•
Do not set up the unit if high winds
WARNING
are expected. High winds can cause
the light to tip or fall causing severe injury.
•Light extends upward. Verify the area above light is
open and clear of overhead wires and obstructions
before raising.
•Chemical Burn Hazard. Keep batteries away from
children.
•This tool contains a lithium button/coin cell battery.
A new or used battery can cause severe internal
burns and lead to death in as little as 2 hours if
swallowed or enters the body. Always secure the bat-
tery cover with all screws. If it does not close securely,
stop using the tool, remove the batteries, and keep it
away from children. If you think batteries may have
been swallowed or entered the body, seek immediate
medical attention.
• Always use common sense and be cautious when
using tools. It is not possible to anticipate every situation
that could result in a dangerous outcome. Do not use this
tool if you do not understand these operating instructions
or you feel the work is beyond your capability; contact
Milwaukee Tool or a trained professional for additional
information or training.
•Maintain labels and nameplates. These carry im-
portant information. If unreadable or missing, contact
a MILWAUKEE service facility for a free replacement.
EXTENSION CORDS
Grounded tools require a three wire extension
cord. Double insulated tools can use either a two
or three wire extension cord. As the distance from
the supply outlet increases, you must use a heavier
gauge extension cord. Using extension cords with
inadequately sized wire causes a serious drop in
voltage, resulting in loss of power and possible tool
damage. Refer to the table shown to determine the
required minimum wire size.
The smaller the gauge number of the wire, the greater
the capacity of the cord. For example, a 14 gauge
cord can carry a higher current than a 16 gauge cord.
When using more than one extension cord to make
up the total length, be sure each cord contains at
least the minimum wire size required. If you are using
one extension cord for more than one tool, add the
nameplate amperes and use the sum to determine
the required minimum wire size.
Guidelines for Using Extension Cords
• If you are using an extension cord outdoors, be sure
it is marked with the suffix "W" to indicate that it is
acceptable for outdoor use.
• Be sure your extension cord is properly wired and in
good electrical condition. Always replace a damaged
extension cord or have it repaired by a qualified
person before using it.
• Protect your extension cords from sharp objects,
excessive heat and damp or wet areas.
• When stringing lights together, consider the total
Amperes draw when selecting the extension cords.
Recommended Minimum Wire Gauge
For Extension Cords*
Nameplate Amps
0 - 2.0
2.1 - 3.4
3.5 - 5.0
5.1 - 7.0
7.1 - 12.0
12.1 - 16.0
16.1 - 20.0
* Based on limiting the line voltage drop to five volts at 150%
of the rated amperes.
READ AND SAVE ALL INSTRUCTIONS
FOR FUTURE USE.
GROUNDING
Improperly connecting the ground-
DANGER
ing wire can result in the risk of
electric shock. Check with a qualified electrician
if you are in doubt as to whether the outlet is
properly grounded. Do not modify the plug pro-
vided with the tool. Never remove the grounding
prong from the plug. Do not use the tool if the
cord or plug is damaged. If damaged, have it
repaired by a MILWAUKEE service facility before
use. If the plug will not fit the outlet, have a
proper outlet installed by a qualified electrician.
Grounded Tools (Three-Prong Plugs)
Tools marked "Grounding Required" have a three
wire cord and three prong grounding plug. The plug
must be connected to a properly grounded outlet
(See Figure A). If the tool should electrically mal-
function or break down, grounding provides a low
resistance path to carry electricity away from the
user, reducing the risk of electric shock.
The grounding prong in the plug is connected through
the green wire inside the cord to the grounding
system in the tool. The green wire in the cord must
be the only wire connected to the tool's grounding
system and must never be attached to an electrically
"live" terminal.
Your tool must be plugged into an appro-
priate outlet, properly installed and
grounded in accordance with all codes
and ordinances. The plug and outlet
should look like those in Figure A.
3
Extension Cord Length
25'
50'
75'
100'
18
18
18
18
18
18
18
16
18
18
16
14
18
16
14
12
16
14
12
10
14
12
10
--
12
10
--
--
Fig. A
150'
16
14
12
12
--
--
--
Tabla de contenido
