Practical Advice; Maintenance And Service; Maintenance And Cleaning; After-Sales Service And Application Service - Bosch GLI 18V-1200 C Professional Manual Original

Tighten the 1/4" screw. Ensure that the tripod has a firm
footing.
Switching on/off and adjusting the brightness
On/off switch
Function
Press once Switches on the cordless worklight,
dimmed
Press twice Switches on the cordless worklight,
full brightness
Press three times Switches off the cordless worklight
If the cordless worklight has been switched on in dimmed
mode for approx. five minutes, it will be switched off imme-
diately the next time the button is pressed.
Temperature-dependent overload protection
When the permitted operating temperature is exceeded, the
cordless worklight initially reduces the brightness before
switching itself off if required for protection. Let the cordless
worklight cool down and then switch the cordless worklight
back on.
Changing the Button Cell (see figure A)
Make sure that the battery compartment (9) is not
u
damaged when removing the cell.
Make sure that the positive pole of the button cell
u
faces upwards.
A warning will be displayed in the app before the button
cell (10) is fully used up.
To change the button cell (10), unlock the locking mechan-
ism of the battery cover (6) and fold up the battery
cover (5).
Unscrew the screw of the battery compartment cover (12)
and remove the battery compartment cover (11).
Remove the empty button cell and insert a new button cell.
Reattach the battery compartment cover with the screw.
Control Via App
The cordless worklight is fitted with a Bluetooth® module
which enables wireless data transfer to certain mobile
devices with a Bluetooth® interface (e.g. smartphone, tab-
let).
In order to control the cordless worklight via Bluetooth®, you
will need the "Bosch Toolbox" app. Download the app from
the corresponding app store (Apple App Store, Google Play
Store).
Then select the "My Tools" subitem in the app. The display of
your mobile device will show you all subsequent steps re-
quired to connect the cordless worklight to the device.
The following functions will be available when a connection
has been established with the mobile device:
– Remote control
– Time control
– Grouping several cordless worklights
– Personalisation
– Status check, output of warning messages
– General information and settings
Bosch Power Tools
– Management

Practical Advice

Errors – causes and corrective measures
Cause Corrective measures
A Bluetooth® connection cannot be established with the
cordless worklight.
The cordless worklight is not Remove the button cell (10)
emitting a Bluetooth® signal. and battery (8) for 10
seconds.
The cordless worklight cannot be operated via
Bluetooth® even though the battery is inserted and
charged.
The Bluetooth® module is not Press the on/off switch (2)
activated. repeatedly until the cordless
worklight can be operated
via Bluetooth®.
The cordless worklight cannot be switched on after
wireless charging.
The inductively chargeable Remove the battery (8) for
battery has to be re-initial- 10 seconds.
ised.
The PIN for the Bluetooth connection is not working.
The PIN must be reset to Remove the button cell (10)
factory settings. and battery (8) for 10
seconds.

Maintenance and Service

Maintenance and Cleaning

Remove the battery from the power tool before carry-
u
ing out work on the power tool (e.g. maintenance,
changing tool, etc.). The battery should also be re-
moved for transport and storage. There is risk of injury
from unintentionally pressing the on/off switch.
The light source cannot be replaced. If the light source is de-
fective, the entire cordless worklight has to be replaced.
The cordless worklight is maintenance-free and does not
contain any parts that need to be replaced or maintained.
Only clean the cordless worklight's plastic lens with a dry,
soft cloth to prevent damage. Do not use any detergents or
solvents.
If the button cell has fully discharged, replace it with a new
one.

After-Sales Service and Application Service

Our after-sales service responds to your questions concern-
ing maintenance and repair of your product as well as spare
parts. You can find explosion drawings and information on
spare parts at: www.bosch-pt.com
The Bosch product use advice team will be happy to help you
with any questions about our products and their accessor-
ies.
English | 13
1 609 92A 5T4 | (14.10.2020)