Troy-Bilt TB21 EC Manual Del Operador

Troy-Bilt TB21 EC Manual Del Operador

Ocultar thumbs Ver también para TB21 EC:
Idiomas disponibles

Idiomas disponibles

Enlaces rápidos

Removing Unit From Carton
Assemble The Unit
Slot
Bracket
1 1
2
Remove all contents from
Slide shield's slot onto
carton.
mounting bracket. Rotate
shield onto shaft. Push
square bolt through shield
and bracket. Tighten
washer and wing nut
onto bolt.
Assemble The Unit
40:1
1 Gallon
3.2 oz
5
6
Mix thoroughly in a separate
Place unit on a level surface.
fuel can:
Fill fuel tank.
– 3.2 fl. oz. of 2-cycle
engine oil
– 1 gallon of fresh
unleaded gasoline (less
than 30 days old)
NOTE: Do not mix directly in
the unit fuel tank.
Starting The Unit
1 9
10
Crouch in starting position.
SQUEEZE and HOLD
throttle for ALL further
steps.
Reloading The Line*
Spool
Spring
Inner
Reel
3"-4"
Bump
Knob
1 1
2
Unscrew bump knob
Insert 10' of 0.095"
®
counterclockwise. Remove
SplitLine
through hole in top
inner reel and spring.
of reel. Pull most of line
through hole until 3"-4"
remains.
Reloading The Line
Replacement SplitLine
Part #49U1341K006
For single line installation, refer to Line Installation
section of this manual.
For replacement spool installation, refer to
Installing a Prewound Reel section of this manual.
*This is to assist in the reloading of Splitline® only. These instructions
1 8
are NOT part of the fast assembly instructions. Line does not need to
be installed on the initial assembly and start-up.
Hold the inner reel in place.
Tighten Bump Knob
clockwise.
IMPORTANT: READ OPERATOR'S MANUAL THOROUGHLY AND FOLLOW THE SAFE OPERATION PRACTICES BEFORE OPERATING THE UNIT.
CALL 1-800-828-5500 IN U.S. OR 1–800–668–1238 IN CANADA
769-07922 P00
Operator's Manual
Min. 6"
3
4
Remove the protective cap
Put D-handle on shaft. Move
and gray spacer from the
handle a minimum 6 inches
upper and lower shafts.
away from shaft grip. Insert
Push the attachment into
clamp bolt and tighten the
the coupler. Turn the knob
wing nut.
clockwise to tighten.
Starting The Unit
Primer
Bulb
10 X
7
8
Press primer bulb 10 times,
Move choke lever to
or until fuel is visible
Position 1.
Choke Lever
5 X
11
12
Pull rope 5 times.
Move choke lever to
Position 2 and squeeze
throttle.
3
4
Bend short end and push it
Wind line tightly in direction
into the other hole. Pull tight.
of arrow. Split other end of
®
SplitLine
®
:
NEED HELP?
NO ASSEMBLY TOOLS REQUIRED
Electric Starter or
Power Start Bit Optional!
THESE OPTIONAL ACCESSORIES
ARE SOLD SEPARATELY!
This unit has an alternate starting method
that many find easier to use than pulling a
rope. Please contact a local retailer or call
1-800-828-5500 for more information.
Information may also be found at
www.troybilt.com
Choke Lever
Cutting Head Shield
3-5 X
13
Pull rope 3-5 times to start
engine. Run unit for 30-60
seconds to warm up.
5
Push 6"-7" ends into 0.095"
holding slots.
back 6"-7".
TB21 EC
2-Cycle
Electric Start Capable
Trimmer
On/ Off Switch
Throttle Control
D-Handle
EZ-Link™
Need Help?
Call 1-800-828-5500
DIDN'T START?
Repeat these instructions.
IF engine fails to start after 2 attempts,
move choke lever to position 3 and pull
the starter rope until engine starts
IF unit still fails to start, refer to the
operator's manual for additional starting
and troubleshooting information
Choke Lever
14
15
Continue to squeeze
Continue to squeeze
throttle. Move choke lever
throttle. Run unit for an
to Position 3.
additional 60 seconds to
complete warm-up. Unit
may be used during this
time.
6
7
Insert or slide lines into the
Pull lines firmly to release
eyelets in spool. Insert spring
from holding slots.
and reel into spool.
Starter Rope
Fuel Cap
02/12
Tabla de contenido
loading

Resumen de contenidos para Troy-Bilt TB21 EC

  • Página 11: No Se Requiere De Herramientas Para El Ensamblaje

    TB21 EC Motor de 2 tiempos Con Posibilidad de Arranque Eléctrico Recortador Manual del Operador Sacar la unidad de la caja Ensamblado de la unidad Cuerda de arranque NO SE REQUIERE DE HERRAMIENTAS PARA Tapa de Ranura combustible EL ENSAMBLAJE Interruptor de Min.
  • Página 12: Llamadas A Apoyo Al Cliente

    INDICE DE CONTENIDOS CONSIGNES DE SÉCURITÉ Llamadas a apoyo al cliente ............12 Normas para una operación segura .
  • Página 13: Conozca Su Unidad

    CONOZCA SU UNIDAD INFORMACIÓN DEL ACEITE Y DEL COMBUSTIBLE APLICACIONES INSTRUCCIONES PARA MEZCLAR EL ACEITE Y EL COMBUSTIBLE Como recortadora; Bujía de encendido ADVERTENCIA: Se ha demostrado que el combustible que Silenciador Mango de la • Corte de césped y hierbas delgadas contiene más del 10% de etanol probablemente ocasionará...
  • Página 14: Instrucciones De Operación

    INSTRUCCIONES DE ARRANQUE Y APAGADO INSTRUCCIONES DE MANTENIMIENTO Y REPARACIÓN 10. Mantenga apretado el control del regulador, ponga la palanca del obturador en la Posición 3 (Fig. 8) y haga Bobinado del carrete interior existente Bobina Perilla del exterior funcionar la unidad durante 60 segundos más. La unidad se puede usar durante este paso. topetón 1.
  • Página 15: Limpieza Y Almacenamiento

    INSTRUCCIONES DE MANTENIMIENTO Y REPARACIÓN ACCESORIO OPCIONAL MANTENIMIENTO DEL FILTRO DE AIRE ARRANCADOR ELÉCTRICO Y ACCESORIO DE ARRANQUE ELÉCTRICO OPCIONAL POWER START BIT™ Esta unidad está diseñada para utilizarse, de forma opcional, con un arrancador eléctrico o con un accesorio de ADVERTENCIA: arranque Power Start Bit™, los cuales se venden por separado.
  • Página 16: Warranty Information

    Troy-Bilt LLC garantit ce produit contre tout vice de matière ou de façon pendant une période de deux (2) ans à compter de la date d’achat initiale et elle se réserve le choix de réparer ou de remplacer, à titre...

Tabla de contenido