Idiomas disponibles

Idiomas disponibles

Enlaces rápidos

Removing Unit From Carton
Assemble The Unit
1 1
2
Remove all contents from
Place the shield onto the
the carton.
mount bracket. Securely
screw the 4 shield screws
through the holes on the
mount bracket and into the
shield. Make sure the screws
are tightened equally.
Assemble The Unit
40:1
1 Gallon
3.2 oz
5
6
Mix thoroughly in separate
Place unit on a level surface.
fuel can:
Fill fuel tank.
– 3.2 fl. oz. of 2-cycle
engine oil
– 1 gallon of unleaded
gasoline
NOTE: Do not mix directly in
fuel tank.
Starting The Unit
1 9
10
Crouch in starting position.
SQUEEZE and HOLD
throttle for ALL further
steps.
Reloading The Line*
Quick Instructions to
Replace Trimmer Line
For complete instructions,
refer to Line Installation
section of this manual.
Using 16 ft. of 0.095 in. line; push both
ends through the holes in the bump knob
until they protrude through the eyelets.
IMPORTANT: READ THE OPERATOR'S MANUAL THOROUGHLY AND FOLLOW THE SAFE OPERATION PRACTICES WHILE OPERATING THE UNIT.
IMPORTANT: READ THE OPERATOR'S MANUAL THOROUGHLY AND FOLLOW THE SAFE OPERATION PRACTICES WHILE OPERATING THE UNIT.
NEED HELP?
769-07374 P00
Operator's Manual
Min. 6"
3
4
Remove cap from end of
Put handle on shaft. Move
lower boom. Push cutting
handle a minimum 6 inches
attachment add-on into
away from shaft grip. Insert
coupler. Turn coupler knob
bolt and tighten.
clockwise to tighten.
Starting The Unit
Primer
Choke Lever
Bulb
10 X
7
8
Press primer bulb 10 times,
Move choke lever to
or until fuel is visible
Position 1.
Choke Lever
5 X
11
12
Pull rope 5 times.
Move choke lever to
Position 2 and squeeze
throttle.
Rotate the bump knob
clockwise until all line is
inside the cutting head.
Pull the line until approximately
8 ft. is visible on each side.
CALL 1-800-828-5500 IN U.S. OR 1–800–668–1238 IN CANADA
TB2040 XP
2-Cycle Trimmer
Electric Starter or
Power Start Bit Optional!
THESE OPTIONAL ACCESSORIES
ARE SOLD SEPARATELY!
This unit has an alternate starting method
that many find easier to use than pulling a
rope. Please contact a local retailer or call
1-800-828-5500 for more information.
Information may also be found at
www.troybilt.com
On/ Off Switch
D-Handle
Ez-Link™
Cutting Head Shield
IF unit still fails to start, refer to operator's
Choke Lever
3-5 X
13
14
Pull rope 3-5 times to start
Continue to squeeze
engine. Run unit for 30-60
throttle. Move choke lever
seconds to warm up.
to Position 3.
Align the arrows on the
Using a flat-head screwdriver,
bump knob with the
insert the tip into the line dimple,
spool cover eyelets.
just under the exposed portion of
the line, and pull all the line out.
Hold the spool cover, turn the bump
Start the unit and bump the cutting
knob clockwise to wind the line around
head on the ground until the
the spool until about 5 in. is protruding
desired cutting length is achieved.
from each side of the cutting head.
Starter Rope
Fuel Cap
Throttle Control
ASSEMBLY TOOLS
REQUIRED:
• Phillips screwdriver
• 3/8" Socket and Driver
Need Help?
Call 1-800-828-5500
DIDN'T START?
Repeat these instructions.
IF engine fails to start after 2 attempts,
move choke lever to position 3 and pull
the starter rope until engine starts
manual for additional starting and
troubleshooting information
15
Continue to squeeze
throttle. Run unit for an
additional 60 seconds to
complete warm-up. Unit
may be used during this
time.
10/11
Tabla de contenido
loading

Resumen de contenidos para Troy-Bilt TB2040 XP

  • Página 11: Herramientas De Ensamblaje Necesarias

    TB2040 XP Recortador de 2 Ciclos Manual del Operador Sacar la unidad de la caja Ensamblado de la unidad ¡Arranque eléctrico Cuerda de arranque o accesorio de arranque eléctrico opcional! ¡ESTOS ACCESORIOS OPCIONALES SE VENDEN POR SEPARADO! Interruptor de Esta unidad posee un método de arranque Mín:...
  • Página 12: Alerta De Seguridad

    INDICE DE CONTENIDOS NORMAS PARA UNA OPERACION SEGURA Llamadas a apoyo al cliente ............12 Normas para una operación segura .
  • Página 13: Conozca Su Unidad

    CONOZCA SU UNIDAD INFORMATIONS SUR L'HUILE ET LE CARBURANT Bujía de encendido APLICACIONES INSTRUCCIONES PARA MEZCLAR EL ACEITE Y EL COMBUSTIBLE Como recortadora; Mango de la Silenciador El combustible viejo o mal mezclado son los motivos principales del mal funcionamiento de la unidad. cuerda de •...
  • Página 14 SI VA A UTILIZAR EL ARRANCADOR ELÉCTRICO O ACCESORIO DE POWER START BIT™ OPCIONAL INSTRUCCIONES DE MANTENIMIENTO Y REPARACIÓN 2. Llene el tanque de combustible con gasolina limpia y fresca. Consulte Cómo llenar la unidad de ELIMINACIÓN DE LA LÍNEA combustible.
  • Página 15: Instrucciones De Mantenimiento Y Reparación

    INSTRUCCIONES DE MANTENIMIENTO Y REPARACIÓN RESOLUCIÓN DE PROBLEMAS CAMBIO DE LA BUJIA DE ENCENDIDO CAUSA ACCIÓN 1. Apague el motor y espere que se enfríe. Tome el alambre de la bujía con firmeza y sáquelo de la EL MOTOR NO ARRANCA bujía de encendido.
  • Página 16: Warranty Information

    Troy-Bilt LLC garantit ce produit contre tout vice de matière ou de façon pendant une période de trois (3) ans à compter de la date d’achat initiale et elle se réserve le choix de réparer ou de remplacer, à titre...

Tabla de contenido