Cata IB 603 BK /A Instrucciones Para La Instalación, El Uso, El Mantenimiento página 21

changed further.
If the setting level has been selected using the MINUS (2) button,
the start level is "9" (maximum level). Keep the button pressed
down to lower the active level by 1 every 0.4 seconds. When
setting "0" is reached, there will be no further setting changed.
The setting can only be changed by pressing the MINUS (2) or
PLUS (3) button again.
Switching a cooking zone off
Pressing the UP (3) and DOWN (2) buttons at the same time will
reset the power level to 0. Alternatively, the MINUS button (2)
can be used to reduce the setting level to 0.
If a cooking zone is "hot", "H" and "0" will be alternately
displayed.
Switching-OFF all cooking zones
Pressing the ON/OFF (1) button at any time will cause all
cooking zones to switch off immediately. In the standby- mode
an "H" appears on all cooking zones which are "hot". All other
cooking zone displays are not illuminated.
Wattage settings
The output of the cooking zones can be set in 9 steps which are
indicated by the figures "1" thru "9" by means of LED displays.
Boost function
The booster function can be activated for the required cooking
zone by selecting power level 9 and then pressing the UP (3)
button. By means of this function certain cooking zones are
enabled to receive power over the nominal (the number of
boostable cooking zone depends on the power available on a
partial modules which is to be lees than total hob power ). If the
desired cooking zone has the capacity to activate the booster,
the display shows a "P" symbol. If there is insufficient available
power, the power level indicator for the cooking zone that needs
to automatically reduce power will display "r" for 3 seconds,
following which the power level will decrease to the previous
setting.
The boosting time is limited to 10 min to protect cooking utensils.
After the booster is switched off automatically, the cooking zone
continues operation on power level "9". The booster can be
reactivated after some minutes.
In case that the pan is removed from the cooking zone during
boosting, the boosting function remains active and boosting
time continues.
Residual heat indicator
It is meant to indicate to the user that the glass ceramic has
a dangerous touch temperature in the circumference of a
cooking zone. The temperature will be determined following
a mathematical model and the remaining residual heat will be
indicated by means of "H" on the corresponding display.
Heating-up and cooling down will be calculated dependent on:
· the selected setting („0" to „9")
· the ON/OFF time.
After switching-OFF the cooking zone the respective display
shows "H" until the assigned cooking zone temperature is
mathematically in a uncritical level. (≤ 60°C).
Automatic power OFF function (operating time limitation)
Dependent on the selected setting, every cooking zone will be
switched-OFF after a defined maximum operation time if no
operation of the assigned cooking zone follows within this time
period. Every change of the cooking zone condition (by means
of the PLUS-, MINUS- key) puts back the maximum operation
time of this cooking zone to the initial value of the operating time
limitation.
Protection against unintended switching-ON
· If the electronic control realizes a continuous operation of keys
for approx. 10 seconds, it switches OFF automatically.
- If no cooking zone is activated within 10 seconds of switching
on the touch control, this will revert to stand-by status.
· When the control is switched- ON the ON/OFF-key has priority
over all other keys, so that the control can be switched-OFF
anytime, even in case of multiple or continuous operation of
keys.
· In the stand-by mode a continous operation will not be
signalized. However, before the electronic control can be
switched-ON again, it has to recognize that all keys are not
operated.
Key lock (child safety feature)
◊ Child safety feature:
Key lock:
To activate the child safety lock after switching on the touch
control, press the safety lock button (10) for 1 second and the
safety lock indicator LED will illuminate (11).
The safety lock function may be activated either when cooking
zones are active or when the appliance is fully switched off.
The electronic control remains in a locked condition until it gets
unlocked, even if the control has been switched-OFF and -ON in
the meantime. Also a reset of the control (after a voltage drop)
does not cancel the key lock.
Unlocking for cooking purposes: :
To unlock the touch control, press the safety lock button (10) for
1 second and the safety lock indicator LED will be extinguished
(11).
Audible signal (buzzer)
While the control is in operation the following activities will be
signaled by means of a buzzer:
· normal key activation with a short sound signal.
· 3 short acoustic signals (beeps) for turning off the touch
control.
Timer function (optional)
The timer function works as follows:
·
Timer function for a selected cooking zone, from 1 to 99 min:
at the end of the set time, an acoustic signal will be emitted and
the timed zone will be turned off. All three cooking zones may
be programmed independently to different timer settings. During
the last minute of the set time, the timer display (7) will show the
time remaining in seconds.
Timer programming on cooking zones
It is only possible to set the timer in a single cooking zone at
a time. Activate the timer by pressing UP TIMER (9) or DOWN
TIMER (8). The timer display will show "00" (7) and the symbol
"t" will appear on the power level displays for each cooking zone
for which the timer is being set.
Press the power level UP (3) or DOWN (2) button on the cooking
zone to be timed; the desired zone is selected and the timer
indicator LED illuminates (6) for the selected zone.
Having selected the zone to be timed, press UP TIMER (8) or