List Of Components - Chicco Bubble Nest Manual Del Usuario

INSTRUCTIONS FOR USE
IMPORTANT WARNING:
READ CAREFULLY AND KEEP FOR FUTURE
REFERENCE.
WARNING: BEFORE USE, REMOVE AND DISPOSE OF
ALL PLASTIC BAGS AND PACKAGING MATERIALS
AND KEEP THEM OUT OF REACH OF CHILDREN.
BUBBLE NEST
Bubble Nest is a transformable solution for baby's bath
from the first days of life up to one year of age. With the
stand it can be used inside the shower and without the
stand it fits nicely inside an adult size bathtub.
It is compatible with any shower tray that has internal
measurements of at least 70x70 cm.

LIST OF COMPONENTS

A - Tub/Seat
A1 - T-Bar
A2 - Extractable leg
A3 - Extractable leg suction cups (2x)
A4 - Front suction cups (2x)
A5 - Plug
A6 - Lower T-Bar release tab
A7 - Lower T-Bar slot
A8 - Stand housing slots
A9 - Side T-Bar release buttons
A10 - Release buttons
A11 - Central T-Bar slot
A12 - Side T-Bar slots
B - Upper stand
B1- Joints
B2 - Joint buttons
B3 - Stand inserts
B4 - Upper legs
C - Lower legs (4x)
MAINTENANCE
This product requires periodical maintenance. Cleaning
and maintenance operations must be performed exclu-
sively by an adult.
CLEANING
Periodically wipe the plastic parts clean with a soft
damp cloth. Dry the metal parts after contact with wa-
ter to prevent rust from forming. Do not use solvents or
abrasive products for cleaning.
0 – 6m USE WITH THE STAND
1. Insert lower legs "C" in upper legs "B4", putting light
pressure on the pins found on the ends of the lower
legs until you hear the locking click (Fig.1).
2. Open upper stand "B", moving the front legs away
from the rear legs (Fig.2).
3. Remove T-Bar "A1" installed under tub/seat "A", press-
ing on lower release tab "7"(Fig.3).
4. Insert T-Bar "A1" in the central slot "A11" then in side
slot "A12" (Fig.4), putting light pressure on the bottom
until you hear a locking click (Fig.4A).
5. Place tub/seat "A" on upper stand "B", inserting stand
inserts "B3" inside slot housings "A8" located on tub/
seat "A" until you hear a locking click (Fig.5).
6. Ensure you line up the symbols positioned on the
side wall and on the joints, as shown in figure 6.
7. After using the product, remove plug "A5" to empty
the tub (Fig.7).
6 -12m USE WITH THE STAND
8. Release tub/seat "A" from stand "B", pressing buttons
"B3" and turning tub/seat "A" 180°. Place tub/seat "A"
on upper stand "B", inserting stand inserts "B3" inside
slot housings "A8" located on tub/seat "A" until you
hear a locking click (Fig.8).
The symbols positioned on the side wall and on the
joints can be seen, as shown in figure 6.
Before using the product, remove plug "A5", unscrewing
it from the bottom (Fig.7).
0 – 6m USE IN THE BATHTUB
9. If tub/seat "A" has been installed on the stand, you
need to release it from stand "B" by pressing on but-
tons "A10" (Fig.9).
10. Remove T-Bar "A1", pressing on side buttons "A9" then
pressing on lower tab "A6" (Fig.10).
11. Insert T-Bar "A1" in the lower part of tub/seat "A", en-
suring that it has been properly engaged inside low-
er slot "A7" (Fig.11).
After using the product, remove plug "A5" to empty the
tub (Fig.7).
6 -12m USE IN THE BATHTUB
12. If tub/seat "A" has been installed on the stand, you
need to release it from stand "B" by pressing on but-
tons "A10" (Fig.12).
13. Verify that the T-Bar has been properly inserted in
slots "A11" and "A12" (Fig.13).
14. Activate extractable leg "A2" by pulling it towards
the front of tub/seat "A" and turning it towards the
7