Tabla de contenido
Idiomas disponibles
Idiomas disponibles
4.
Connect the hot lead to the black fixture wire, the neutral lead to the
white fixture wire and ground lead to the green fixture wire. Use only
approved electrical type splices. Use caution to route wires away from
LED driver.
5.
Tighten cord grips securely, assuring a good seal around the cable(s).
Note that any unused cable entries must be properly plugged or sealed to
prevent water entry.
6.
Close reflector by positioning in place and turning fasteners.
7 .
Replace lens in position and latch in place with all latches.
GENERAL WIRING DIAGRAMS
Customer Connections
Outside Of Fixture
NEUTRAL
A
B
(UNSWITCHED) WHITE
A
24"
18 AWG RED
A
UNSWITCHED HOT
18 AWG, 18"
A
SWITCHED OR UNSWITCHED HOT
GREEN\YELLOW
16 AWG, 6"
GROUND
A
GREEN\YELLOW
16 AWG, 18"
NEUTRAL
A
18 AWG, 18"
SWITCHED OR UNSWITCHED HOT
A
18 AWG, 18"
GREEN\YELLOW
16 AWG, 6"
White\Color LED - With Emergency Backup
End User Connections
NEUTRAL
WHITE
A
18 AWG, 18"
NEUTRAL (WHITE)
18 AWG, 18"
BLK
A
SWITCHED OR UNSWITCHED HOT
LINE (BLACK)
GND (GREEN)
GREEN/YELLOW
16 AWG, 6"
GROUND
A
16 AWG, 18"
GREEN/YELLOW
NEUTRAL
A
18 AWG, 18"
WHITE
NEUTRAL (WHITE)
18 AWG, 18"
BLK
A
SWITCHED OR UNSWITCHED HOT
LINE (BLACK)
GND (GREEN)
GREEN/YELLOW
16 AWG, 6"
White\Color LED - No Emergency Backup
MAINTENANCE GENERAL
1.
Disconnect the battery/converter connector during extended periods of
power loss of more than 1 week. If the luminaire is out of service for
more than 1 year, perform the annual test procedure and replace battery
packs as needed. Note: Battery capacity can usually be restored after
approximately three (3) full charge/discharge cycles.
2.
Perform visual, electrical and mechanical inspections on a regular basis.
The environment and frequency of use should determine this. However,
it is recommended that checks be made at least once a year. We
recommend an Electrical Preventive Maintenance Program as described
in the National Fire Protection Association Bulletin NFPA No. 70B:
Recommended Practice For Electrical Equipment Maintenance (www.
nfpa.org).
3.
The lens should be cleaned periodically to ensure continued lighting
performance. To clean, wipe the lens with a clean, damp cloth. If this is
not sufficient, use a mild soap or a liquid cleaner such as Collinite NCF or
Duco #7 . Do not use an abrasive, strong alkaline, or acid cleaner. Damage
may result.
IF 1836 • 10/17
-
LED Board (Red Or Blue)
+
-
LED Board (White)
+
22 AWG RED 17.25"
Battery Disconnect
WHT/BLK
WHT/BLK
RED/WHT (+)
WHT/BLK
BLUE/WHT (-)
Emergency Driver
RED (+)
BLK/ORG
See DWG# 0307496-2 For Driver Prep
BLUE (-)
WHT/BLK
WHT/RED
18"
RED OR RED/BLK (+)
18"
A
A
A
12"
WHITE
RED
18 AWG WHITE
Internal Test SW/Light
NEUTRAL (WHITE)
RED
LED+
BLK
LINE (BLACK)
LED Driver
BLUE
LED-
GND (GREEN)
White
FA8022
TO REFLECTOR PLATE STUD
DRIVER MOUNTINGPLATE
RING TERMINAL CONNECTS TO LED MOUNTING PLATE
NEUTRAL (WHITE)
RED
LED+
WHITE
LED Driver
LINE (BLACK)
BLUE
LED-
BLK
Color
GND (GREEN)
-
LED Board (Red Or Blue)
+
-
LED Board (White)
+
RED
BLACK
22 AWG
22 AWG
17.25"
17.25"
RED (+)
(RED)
LED+
LED Driver
(BLUE)
LED-
BLACK (-)
FA8022
TO REFLECTOR PLATE STUD
DRIVER MOUNTING PLATE
RED (+)
(RED)
LED+
LED Driver
BLACK (-)
(BLUE)
LED-
Copyright © 2017, Eaton's Crouse-Hinds Division
OPERATION
After all mounting and electrical work has been completed and the fixture is
properly closed, power can be applied and the fixture inspected for proper
operation.
A
2- Pole Wago
22 AWG BLACK 17.25"
A
A
Customer Connections
Outside Of Fixture
NEUTRAL
UNSWITCHED HOT
SWITCHED OR UNSWITCHED HOT
GROUND
RED (+)
22 AWG, 17.25"
BLACK (-)
22 AWG, 17.25"
NOTE:
Emergency Driver Wires Shall Be
Trimmed Down To 5 Inches.
A
2- Pole Wago
RED
BLACK
22 AWG
22 AWG
17.25"
17.25"
End User Connections
NEUTRAL
GROUND
4.
Visually check for undue heating evidenced by discoloration of wires or
other components, damaged parts or leakage evidenced by water or
corrosion in the interior. Replace all worn, damaged or malfunctioning
components, and clean gasket seals before putting the luminaire back into
service.
5.
Electrically check to make sure that all connections are clean and tight.
Mechanically check that all parts are properly assembled.
6.
Check and re-torque all mounting hardware.
7 .
To prevent heat build-up, remove dust from the LED housing using a soft
brush or air pressure.
8.
Ensure power is removed before conducting any service work, such as
removing or installing drivers and replacing any components.
EMERGENCY DRIVER INFORMATION
FPS emergency luminaires are supplied with an emergency driver. Disconnect
the battery/converter connector prior to performing maintenance. This will
disconnect the charged battery from the LEDs. The emergency driver must be
checked periodically to ensure that it is working properly.
22 AWG, 8"
-
LED Board
22 AWG, 8"
+
BLACK (-)
-
LED Board
+
RED (+)
WHT/BLK
WHT/BLK
18 AWG WHITE
A
B
(UNSWITCHED) WHITE
24"
Emergency Driver
BLK/ORG
See DWG# 0307496-2 For Driver Prep
WHT/BLK
WHT/RED
18"
A
WHITE
A
A
24"
12"
18 AWG RED
18 AWG WHITE
Internal Test SW/Light
A
NEUTRAL (WHITE)
18 AWG, 18"
BLK
A
LINE (BLACK)
GND (GREEN)
16 AWG, 6"
GREEN\YELLOW
FA8022
A
GREEN\YELLOW
DRIVER MOUNTINGPLATE
16 AWG, 18"
RING TERMINALS CONNECT TO STUD ON MOUNTING PLATE
White LED - With Emergency Backup
22 AWG, 8"
-
LED Board
22 AWG, 8"
+
BLACK (-)
-
LED Board
+
RED (+)
18 AWG, 18"
A
WHITE
NEUTRAL (WHITE)
18 AWG, 18"
BLK
A
LINE (BLACK)
HOT
GREEN/YELLOW
GND (GREEN)
16 AWG, 6"
FA8022
DRIVER MOUNTINGPLATE
GREEN/YELLOW
A
16 AWG, 18"
White LED - No Emergency Backup
A
2- Pole Wago
-
+
22 AWG RED 17.25"
22 AWG BLACK 17.25"
Battery Disconnect
A
A
WHT/BLK
RED/WHT (+)
BLUE/WHT (-)
RED (+)
BLUE (-)
18"
RED OR RED/BLK (+)
A
RED
EM DRIVER RED WIRE
5"
EM DRIVER BLUE WIRE
5"
RED
LED+
LED Driver
BLUE
LED-
TO REFLECTOR PLATE STUD
NOTE:
Emergency Driver Wires Shall Be
Trimmed Down To 5 Inches.
A
2- Pole Wago
-
+
RED
BLACK
22 AWG
22 AWG
17.25"
17.25"
(RED)
LED+
LED Driver
(BLUE)
LED-
TO REFLECTOR PLATE STUD
Page 2
Tabla de contenido
