Tabla de contenido
Idiomas disponibles
Idiomas disponibles
2.2
Operating conditions
FX RANGE pumps are suitable for continuous operation always immersed in the pumped liquid. The FX RANGE pumps allow operation
with the motor NOT IMMERSED for short periods (10min).
pH value: 6.5-12 (Warning: indicative range, the pH value alone is not exhaustive in defining the aggressiveness of the pumped liquid)
Temperature of the operating liquid: 0 °C to +50 °C (non-Ex versions only).
For short periods a temperature of up to +60 °C is permissible (non-Ex versions only).
Explosion-proof pumps must never pump liquids of a temperature higher than +40 °C.
Ambient temperature
For non-explosion proof pumps, the ambient temperature may exceed +40 °C for a short period.
For explosion-proof pumps, the ambient temperature on the installation site must be in the range from 0°C + 40 °C.
Density and viscosity of the pumped liquid: viscosity and density comparable to those of water.
Flow velocity
It is advisable to keep a minimum flow velocity to avoid sedimentations in the piping system. Recommended flow velocities:
• in vertical pipes: 1.0 m/s
• in horizontal pipes: 0.7 m/s
Operating mode
Maximum 20 starts per hour.
FOR FURTHER LIMITATIONS OF THE OPERATING RANGE, REFER TO THE IDENTIFICATION PLATE.
3. DELIVERY AND HANDLING
3.1
Transportation
Before lifting the pump, check that the tools and equipment used for handling, lifting and lowering it into the sinkhole
are suitable for the weight to be lifted, efficient and complying with the applicable safety laws.
The weight of the pump is declared on the pump identification plate and on the label on the packaging.
Always lift the pump by its lifting bracket or by means of a fork-lift truck if the pump is fixed on a pallet. Never lift the
pump by means of the motor cable or the hose/pipe.
3.2
Storage
During long periods of storage, the pump must be protected against moisture and heat.
Storage temperature: -30 °C to +60 °C. If the pump has been in use, the oil should be changed before storage. After a long period of
storage, the pump should be inspected before it is put into operation. Make sure that the impeller can rotate freely.
The impeller may have sharp edges – wear protective gloves.
If stored outside the limits indicated, pay particular attention to the conditions of the mechanical seal, the O-rings, the oil and the cable gland.
4. INFORMATION ON PRODUCTS WITH THE EX MARKING
Marking:
0477:
code identifying the body that checks the production site;
explosion-proof appliance designed for use in a potentially explosive atmosphere;
II: group.
identifies an electrical appliance for use in an environment other than mines with possible presence of firedamp;
2: category.
pump designed for use in places where it is probable that there will be explosive atmospheres caused by mixtures
of air and gas, vapours or mists, or mixtures of air and dust;
G: gas.
the pump is protected in environments with gas, vapours or inflammable mists;
EX:
explosion-proof appliance designed for use in a potentially explosive atmosphere;
db:
electrical constructions for potentially explosive atmospheres – Explosion-proof housings "d";
h:
non electrical constructions for potentially explosive atmospheres – Protection with immersion in liquid "h";
IIB:
characteristic of the gas for which the appliance is intended;
T4:
corresponds to 135℃, and is the maximum surface temperature that can be safely reached by the pump;
X
The letter "X" on the certificate indicates that the appliance is subject to special conditions for safe use. The conditions
are mentioned in the certificate and in the installation and operating instructions.
Gb:
Level of protection of the appliances, appliances for explosive gas atmospheres having a "HIGH" protection level.
CE 0477 II2G
Ex db IIB T4 Gb
Ex h IIB T4 Gb
EPT 20 ATEX 3715 X
ENGLISH
12
Capítulos
Tabla de contenido
