Worx WX094 Manual Del Usuario página 5

PRODUCT SAFETY
GENERAL POWER TOOL
SAFETY WARNINGS
WARNING Read all safety warnings
and all instructions. Failure to follow the
warnings and instructions may result in electric
shock, fire and/or serious injury.
Save all warnings and instructions for future
reference.
The appliance is only to be used with the power
supply unit provided with the appliance.
IMPORTANT
READ CAREFULLY BEFORE USE.
KEEP FOR FUTURE REFERENCE.
Safe operating practices
1) Training
a) Read the instructions carefully. Be familiar
with the controls and the correct use of the
machine.
b) Never allow children, persons with reduced
physical, sensory or mental capabilities or
lack of experience and knowledge or people
unfamiliar with these instructions to use the
machine, local regulations may restrict the age
of the operator.
c) Never operate the machine while people,
especially children, or pets are nearby.
d) Keep in mind that the operator or user is
responsible for accidents or hazards occurring
to other people or their property.
2) Preparation
a) While operating the machine, always wear
substantial footwear and long trousers. Do not
operate the machine when barefoot or wearing
open sandals. Avoid wearing clothing that is
loose fitting or that has hanging cords or ties.
b) Do not wear loose clothing or jewellery that
can be drawn into the air inlet. Keep long hair
away from the air inlets.
c) Obtain ear protection and safety glasses. Wear
them at all times while operating the machine.
d) Operate the machine in a recommended
position and only on a firm, level surface.
e) Do not operate the machine on a paved or
gravel surface where ejected material could
cause injury.
f) Before using, always visually inspect to see,
that the fasteners are secure, the housing is
undamaged and that guards and screens are in
place. Replace worn or damaged components
in sets to preserve balance. Replace damaged
or unreadable labels.
3) Operation
a) Before starting the machine, make certain that
the feeding chamber is empty.
b) Keep your face and body away from the feed
3-speed Workshop Blower
intake opening.
c) Do not allow hands or any other part of the
body or clothing inside the feeding chamber,
discharge chute, or near any moving part.
d) Keep proper balance and footing at all times.
Do not overreach. Never stand at a higher level
than the base of the machine when feeding
material into it.
e) Always stand clear of the discharge zone when
operating this machine.
f) If the machine should start making any unusual
noise or vibration, immediately shut off the
power source and allow the machine to stop.
Remove the battery pack from the machine
and take the following steps before restarting
and operating the machine:
i) inspect for damage;
ii) replace or repair any damaged parts;
iii) check for and tighten any loose parts.
g) Do not allow processed material to build up in
the discharge zone; this may prevent proper
discharge and can result in kickback of material
through the intake opening.
h) If the machine becomes clogged, shut-off the
power source and remove the battery pack
from the machine before cleaning debris.
i) Never operate the machine with defective
guards or shields, or without safety devices.
j) Keep the power source clean of debris and
other accumulations to prevent damage to the
power source or possible fire.
k) Do not transport this machine while the power
source is running.
l) Always disconnect the machine from the
power supply (e.g. remove the battery pack
from the machine)
- whenever you leave the machine,
- before clearing blockages or unclogging chute,
- before checking, cleaning or working on the
machine.
m) Avoid using the machine in bad weather
conditions especially when there is a risk of
lightning.
4) Maintenance and storage
a) keep all nuts, bolts and screws tight to be sure
the appliance is in safe working condition.
b) Replace worn or damaged parts.
c) Use only genuine replacement parts and
accessories.
d) Store the machine in a dry place out of the
reach of children.
e) When the machine is stopped for servicing,
inspection, or storage, or to change an
accessory, shut off the power source,
disconnect the machine from the supply and
make sure that all moving parts are come to
a complete stop. Allow the machine to cool
before making any inspections, adjustments,
etc. Maintain the machine with care and keep it
clean.
f) Store the machine in a dry place out of the
reach of children.
5
EN