Technical Data; Attachment And Operation - Scheppach TPH900 Traducción De Las Instrucciones Originales

6. Technical data

TPH900
Technical data
Cutting data hedge trimmer
Cutting circle diameter mm
Angle adjustment °
Cutting length mm
Max. cutting speed max. min
-1
Power unit
Engine V / Hz
Max. engine output kW
Weight hedge trimmer kg
Subject to technical changes!
Information concerning noise
according to relevant standards:
Sound pressure L = 90 dB(A)
pA
Sound power L = 105 dB(A)
WA
Uncertainty K = 3 dB(A)
PA
Wear ear-muffs.
The impact of noise can cause damage to hearing.
Vibrations:
Hedge trimmer:A = Front 2,72 m/s
hv
Uncertainty K = 1,5 m/s
2
PA
Reduce noise generation and vibration to a minimum!
• Use only equipment that is in perfect condition.
• Maintain and clean the equipment regularly.
• Adopt your way of working to the equipment.
• Do not overload the equipment.
• Have the equipment checked if necessary.
• Switch off the equipment when not in use.
• Wear gloves.
In these operating instructions we have marked the
places that have to do with your safety with this sign: m

7. Attachment and operation

1 Assemble the handle on the machine. Fig. 2-3
• Install the front handle as shown on the image 2.
• Make sure that you align the pin with the hole. Tigh-
ten the screws only loosely before you have the
most comfortable working position set to the risers.
The front handle should be aligned as in pictures
2+3 shown, then tighten the screws.
2. Mounting the shaft. Fig. 4
• Pull out the locking pin (a) and press the lower part
of the shaft (b) downward until the locking pin en-
gages. The bolt (a) is in the right position when it is
fully seated in the bore.
• Lastly, tighten the knob (d) securely.
3. Fit the belt. Fig. 13-15
• The Combined gasoline grass trimmer, pole saw,
brush cutter must be used with the strap.
• Balance the machine when the tool is switched off.
 www.scheppach.com  [email protected]  +(49)-08223-4002-99  +(49)-08223-4002-58
15
-90°/0°/+45 (135°)
410
1000
230 - 240 / 50
0,9
5,3
emission measured
Rear 3,05 m/s
2 2
• Wear the shoulder strap.
• Adjust the strap length so that the snap hook (k) is
about a hand's breadth below the right hip.
• Hang the petrol brush cutter on a hook.
• Hang the machine.
• When standing in a normal working posture, the blade
should touch the ground during normal working position.
• Thereby, it is important that the petrol brush cutter is
always well balanced.
• For operation, hook the petrol brush cutter into the
snap hook (k) of the carrying strap while the engine
is running.
• ATTENTION! In an emergency, the safety latch (l)
can be pulled from the harness. The machine then
detaches immediately from the carrying strap and
falls to the ground.
6. Mounting the hedge trimmer (Fig. 40-42)
• Remove the screw (d), align the holes (c) so that they are
flush and screw the screw (d) back in.
• Place the hedge trimmer (15) precisely as shown in
Figure 40 on the connecting rod (3).
• Tighten with screw (a).
• Adjust the slope by unlocking the lock (Fig. 41)
• The hedge trimmer can be tilted from 0 ° to 90 ° (Fig.42).
ASSEMBLY
When assembling this machine, please follow the inst-
ructions for assembly printed.
Assemble the handle on the machine Fig 3-4
Open the screw holder (17)
Install the front handle (11) at your desired positon and
close the srew holder (17) after this. Screw down the
screw handle (9) for a fix position.
Assemble the extansion / hedge trimmer Fig 5-6
Put the two tubes together. Please make sure that the
metal ball (4) and the bore are on one line. Push them
together until the drive shaft(3) are locked. If you don't
find the correct position please turn the tubes. The me-
tal ball (4) have to lock at the bore. It's only allowed to
use the device if you locked the metal ball (4). Fix the
position with the screw handle (9)
Angle adjustment Fig 7-8
If you want to change the angle pull the switch (7) to
yourself and at the same time press the unlocking
switch, now you can change to 7 different angel for a
perfect work balance. Attention. Only change the angel
if the motor is not connect.
The belt install Fig 9+12
It's only allowed to work with the device if the belt is in-
stalled. Balance out the device before you start .
Wear the belt like in the picture.
The device is not allowed to touch the ground during
normal work attitude.
• ATTENTION! In an emergency, the safety latch (l)
can be pulled from the harness. The machine then
detaches immediately from the carrying strap (9)
GB 23