DMG MixStar-eMotion
Setting the timer
The unit provides memory for 99 timer settings. The timers are used to
set the specific working time [B] and time in mouth [C] for the materi-
al used. The maximum time setting is 9:59 minutes. An acoustic signal
indicates when the set time expires (0:00) and the timer is reset to the
previous time setting. The previous time setting kept in memory even
when the unit is turned off. You assign your settings to a fixed program
memory (D) and access them by recalling the respective program. The
unit can be operated with both, one, or none of the timers. The device
is supplied with preconfigured programs according to the DMG mate-
rial specifications.
1. Press the Menu button [10] briefly. The program display is selected
and blinks.
2. Select a program memory to store the timer settings.
Use the Plus button [8] and Minus button [9] to scroll through the
programs. Keeping either of the buttons pressed scrolls through
the programs in steps of 10. Pressing one of the two buttons briefly
opens one setting at a time.
3. Pressing the Menu button [10] again acknowledges the program
selection. Timer 1 is selected and blinks. If the timer is selected
pressing the Plus button [8] or Minus button [9] will increase or
decrease the time setting in increments of seconds to the next
minute. Keeping the button pressed counts in increments of min-
utes. Pressing one of the buttons again sets the seconds. Pressing the
Menu button [10] briefly selects Timer 2 which is set as described
above. For the working time and time in mouth values please refer
to the material manufacturer's instructions. When programming
Timer 2 to the specified setting time please remember to add the
required transfer time (end of mixing process until insertion into the
mouth).
4. Pressing the Menu button [10] closes the menu and saves the
settings under the respective memory number. A short acous-
tic signal confirms that the settings are saved.
If you press the Start/Stop button [5] before saving the settings the
menu closes. Unsaved settings will be lost.
Program presets
Currently the device is supplied with six preconfigured programs.
Program
Material
P1
Honigum
-Heavy
®
Honigum
-Heavy
®
P2
Fast
Honigum
-
®
P3
MixStar Putty
18
Recommend-
Working time
ed time in
mouth
2:15 min
3:15 min
1:15 min
2:00 min
1:45 min
3:15 min
Program
Material
P4
Honigum
-Mono
®
P5
StatusBlue
®
Silagum
-
®
P6
MixStar Putty
Soft
These preconfigured settings can be changed. When setting Timer 2 to
the specified setting time please remember to add the required transfer
time (end of mixing process until insertion into the mouth).
When you reset the device to the factory settings the settings are revert-
ed back to the preconfigured values.
Selecting programs
1. Press the Menu button [10] briefly. The program display is selected
and blinks.
2. Select the desired program by pressing the Plus button [8] or the
Minus button [9], and scroll through the programs. Keeping the but-
ton pressed counts in increments of 10. Pressing one of the two but-
tons briefly opens one setting at a time.
3. Pressing and holding the Menu button [10] closes the menu and
selects the corresponding program.
Operation without the timers
If none of the timers are used they can be hidden from the display to pro-
vide a better overview. To do that, press the Minus button [9] to set the
program display to P— (see »Selecting programs«), and save the set-
tings by pressing the Menu button [10]. After you press the Start/Stop
button both timers disappear from the display. This setting will remain
active even after the unit is restarted. By pressing the Menu button you
can return to the setting mode and reactivate the timer symbols in the
display.
Restart
The unit can be restarted after it was turned off on the main switch and
remained off for a minimum of 5 seconds.
English
Recommend-
Working time
ed time in
mouth
2:00 min
3:15 min
1:15 min
1:45 min
2:00 min
3:30 min