Unpacking/ Assembly; Starting The Machine - Husqvarna TF545D Manual De Usuario

Note: In the constant desire to improve
the products, the manufacturer states
that the whole of this manual is not
contractual and reserves the right to
modify th especifications
machines without notice.
Unpacking
1• 1
WARNING:
Take care not to cut the
cables or
machine's paintwork when
cutting the edges of the
case.
Ref. Contents of the case
A
Engine Parts
B Sub Holder 1st
C Holder Main Comp
D Lower Tidy Cover
E
Drag Bar
F Tine Cover
G Tine Cover Bracket FR.
H Lever Shifting
I Blades
J Wheel
K Connection Joint
L Extionsion Cover
M
Side Cover
N Locking Handle
O Tine Cover Bracket RR.
P Rubber Cable Holder
Q
Sub Holder 1st
R
Connecting Plate
S Hardware Bag Tines only
T Hardware Bag
W Tool Bag
U
Battery Cover-TF545DE
Filling with engine oil
and checking the level
2• 1
Filling with gearbox
2• 2
Topping up the petrol
Recommend to USE
2• 3
No.0 diesel for summer,
No.-10 diesel for winter.
Add oil to the air filter
Filling the oil to Oil Level
2• 4

UNPACKING/ ASSEMBLY

1• 2
of the
1 2 3
4 5 6
scratch the
7
8 Fitting the connecting joint.
9 Fitting the drag bar.
10 Fitting the handle bar.
11 12
13 Fitting the clutch control.
Turn to proper side and fasten the bolt.
14 15
16 17
18 19
20
21 Fitting the shifting lever.
22 PTO assemble for accessories.
coil

STARTING THE MACHINE

2• 5
oil
2• 6
2• 7
2• 8
Assembling
WARNING:
Inappropriate assembly of
this rotary tiller could
cause severe injuries.
Ensure that you follow all
the instructions carefully.
Fitting the tine blades.
Illustrations only shows
assembly of the tin blades on
the right side.
Make sure that sharp edges
face one side on both Right
and Left side tines.
Note: Please pay attention to
distinguish the Sub Holder 1st
and Sub Holder 2nd.
Adjusting the position of
the handle bar.
Fitting the lower tidy cover.
1. Tidy the cables,
2. Put on the rubber holder
properly,
3. Put on the cover, and fasten
with bolt.
Fitting the tine cover.
Do not tighten the bolt
immediately after installed. Install
all 4 bolts and nuts first, then
tighten one by one.
Shifting lever
Put the lever to gear N.
Throttle control
Put the lever to:
Open the fuel cap
Start the engine
Electric start – TF545DE
Press the decompression lever
down and release, then turn the key
23
Connecting wire to battery -
23
TF545DE.
Connect the black wire to the
negative pole (pole -) and the red
wire to the positive pole (pole +)
oo the battery. Recommended
battery type is 28AH, 12V.
WARNING:
After assembling the machine
completely, tighten all the bolts
and screws with moderation:do
not overtighten.
Note: Any dismantling operation must
only be performed by a Husqvarna
workshop.
of the components
1• 3
1 - Engine
2 - Tine cover
3 - Handle
4 - Extension cover
5 - Blades
6 - Drag bar
7 - Upper tidy cover
8 - Lever shifting
9 - Bumper
1 - Clutch control
11 - Throttle control
12 - Reverse control
13 - Side cover
14 - Lower tidy cover
15 - Battery – TF545DE
1• 4
1• 3
Change the blades with wheels when
transporting
Recoil start – TF545D
1. Press the decompression lever down
and hold by hand.
2. Pull the starting handle slowly until you
feel resistance, then return it slowly, do it
like this three times, and release the
decompression lever at last time.
3. Then press down the decompression
lever and release
4. Pull the handle hard and fast, and pull it
all the way out. Use both hands if
necessary
WARNING:
When the machine starts,
remain within the safety
.
to ON
zone.
Description
Type plate
Transport wheel