Bosch PST 750 PE Manual Original página 14

Ocultar thumbs Ver también para PST 750 PE:
Tabla de contenido
Idiomas disponibles
  • ES

Idiomas disponibles

  • ESPAÑOL, página 24
OBJ_BUCH-1065-005.book Page 14 Thursday, June 13, 2013 9:50 AM
14 | English
Technical Data
Jigsaw
PST 750 PE
Article number
3 603 CA0 5.. 3 603 CA0 1..
"Cut Control"
Stroke rate control
Orbital action
Rated power input
W
Output power
W
-1
Stroke rate at no load n
min
0
Stroke
mm
Cutting capacity, max.
– in wood
mm
– in aluminium
mm
– in non-alloy steel
mm
Bevel cuts (left/right),
max.
°
Weight according to
EPTA-Procedure
01/2003
kg
Protection class
The values given are valid for a nominal voltage [U] of 230 V. For differ-
ent voltages and models for specific countries, these values can vary.
Noise/Vibration Information
Measured sound values determined according to EN 60745.
Typically the A-weighted noise levels of the product are:
Sound pressure level 85 dB(A); Sound power level 96 dB(A).
Uncertainty K =3 dB.
Wear hearing protection!
Vibration total values a
(triax vector sum) and uncertainty K
h
determined according to EN 60745:
2
Cutting board: a
=13 m/s
, K=3 m/s
h
2
Cutting sheet metal: a
=7 m/s
, K=1.5 m/s
h
The vibration emission level given in this information sheet has
been measured in accordance with a standardised test given in
EN 60745 and may be used to compare one tool with another.
It may be used for a preliminary assessment of exposure.
The declared vibration emission level represents the main ap-
plications of the tool. However if the tool is used for different
applications, with different accessories or poorly maintained,
the vibration emission may differ. This may significantly in-
crease the exposure level over the total working period.
An estimation of the level of exposure to vibration should also
take into account the times when the tool is switched off or
when it is running but not actually doing the job. This may signif-
icantly reduce the exposure level over the total working
period.
Identify additional safety measures to protect the operator
from the effects of vibration such as: maintain the tool and the
accessories, keep hands warm, organise work patterns.
Declaration of Conformity
We declare under our sole responsibility that the product de-
scribed under "Technical Data" is in conformity with the fol-
lowing standards or standardization documents: EN 60745
2 609 007 296 | (13.6.13)
according to the provisions of the directives 2011/65/EU,
2004/108/EC, 2006/42/EC.
PST 800. PEL
Technical file (2006/42/EC) at:
Robert Bosch GmbH, PT/ETM9,
D-70745 Leinfelden-Echterdingen
Henk Becker
Executive Vice President
Engineering
530
530
290
290
500 –3000
500 –3000
20
20
Robert Bosch GmbH, Power Tools Division
D-70745 Leinfelden-Echterdingen
75
80
Leinfelden, 29.05.2013
12
12
5
5
Assembly
 Before any work on the machine itself, pull the mains
45
45
Replacing/Inserting the Saw Blade
1.9
1.9
 When mounting the saw blade, wear protective gloves.
/II
/II
Selecting a Saw Blade
An overview of recommended saw blades can be found at the
end of these instructions. Use only T-shank saw blades or saw
blades with 1/4" universal shank (U-shank). The saw blade
should not be longer than required for the intended cut.
Use a thin saw blade for narrow curve cuts.
Inserting the Saw Blade (see figure A1)
 Clean the shank of the saw blade before inserting it. An
If required, remove the dust cover 9 (see "Dust Cover").
2
,
Push the saw blade holder 13 upward in the direction of the
2
.
arrow. Insert the saw blade 15 (teeth in cutting direction) to
the stop into the saw blade holder.
While inserting the saw blade, pay attention that the back of
the saw blade is positioned in the groove of the guide
roller 14.
 Check the tight seating of the saw blade. A loose saw
Removing the Saw Blade (see figure A2)
Push the saw blade holder 13 upward in the direction of the
arrow and remove the saw blade 15.
If the saw blade is wedged or jammed when removing, set ad-
justing lever 7 to maximum orbital action and press the saw
blade holder 13 lightly toward the front (max. 2 mm).
Saw Blade Storage (see figure B)
(PST 800 PEL/PST 8000 PEL)
Up to six saw blades with lengths to 110 mm can be stored in
the saw blade storage 5. Insert the saw blades with the T-shank
into the recess of the saw blade storage intended for this. Up to
three saw blades can be placed on top of each other.
Shut the saw blade storage and slide it to the stop into the
opening of the base plate 6.
Helmut Heinzelmann
Head of Product Certification
PT/ETM9
plug.
Danger of injury when touching the saw blade.
unclean shank cannot be fastened securely.
blade can fall out and lead to injuries.
Bosch Power Tools
Tabla de contenido
loading

Este manual también es adecuado para:

Pst 800 pelPst 8000 pelWeu pst 800 pel

Tabla de contenido