Idiomas disponibles
Idiomas disponibles
Enlaces rápidos
Installation Guide
PREPARATION
1.
Record your model number for future reference.
2.
DANGER: Risk of electric shock. To avoid electric shock, the power must be turned off at the circuit breaker or fuse box
before beginning the installation procedure.
3.
DANGER: Risk of electric shock. To avoid electric shock, the outlet box must be properly grounded.
4.
Important Information. Inspect the product for any damages. This product is for indoor use only. Observe all local codes.
TOOLS AND MATERIALS NEEDED
Phillips &
Flathead
Screwdriver
FIXTURE INSTALLATION
1.
Remove the fixture and parts bag(s) from the carton. Put them
onto a clean and soft cloth to protect finish. Confirm all parts
are included.
2.
Attach mounting plate (B) onto outlet box with screws (C).
Ground screw (J) is as shown.
3.
NOTICE: To avoid short circuit, make sure wires are not exposed.
Fasten fixture green or bare ground wire to the green or bare
copper wire in outlet box with wire nut (A) or fasten onto
ground screw (J) on mounting plate.
4.
NOTICE: To avoid short circuit, make sure wires are not exposed.
Fasten fixture white wire to the white wire in outlet box with
wire nut (A). Wrap the wire connector with electrical tape so
that the tape seals the end of wire nut (A), see diagram.
5.
NOTICE: To avoid short circuit, make sure wires are not exposed.
Fasten the fixture black wire to the black wire in outlet box with
wire nut (A). Wrap the wire connector with electrical tape so
that the tape seals the end of wire nut (A), see diagram.
6.
Press together the two connectors (D).
7.
Tuck wires carefully inside outlet box. Attach the canopy (I) onto
mounting plate (B) by securing screws (E).
8.
Install glass (F) and (H) onto glass holder (G) by turning until the
connection is tight.
9.
Restore power to circuit at breaker or fuse box.
WARNING: For dimming of this fixture, only compatible dimming devices as outlined on the spec sheet are allowed. Visit
www.kohler.com to view the spec sheet.
CLEANING
Please clean fixture with a soft and dry cloth ONLY. Clean glass with a mild soap.
USA/Canada: 1-800-4 KOHLER
www.kohler.com
Please see next page for a larger installation image
Small
Slip Joint
Adjustable
Pliers
Wrench
Electrical
Wire
Current
Cutter/stripper
Tester
Approved fastener
(Wire nut)
SKU#23464
Electrical
Tape
Electrical tape
1408415_2
Manuales relacionados para Kohler 23464
Resumen de contenidos para Kohler 23464
- Página 1 Restore power to circuit at breaker or fuse box. WARNING: For dimming of this fixture, only compatible dimming devices as outlined on the spec sheet are allowed. Visit www.kohler.com to view the spec sheet. CLEANING Please clean fixture with a soft and dry cloth ONLY. Clean glass with a mild soap.
- Página 2 Installation Guide SKU#23464 USA/Canada: 1-800-4 KOHLER 1408415_2 www.kohler.com...
- Página 3 à fusibles. AVERTISSEMENT : Pour la variation de ce luminaire, seuls les dispositifs de variation compatibles décrits dans la fiche technique sont autorisés. Visitez www.kohler.com pour consulter la fiche technique. NETTOYAGE Veuillez nettoyer le projecteur avec un chiffon doux et sec UNIQUEMENT. Nettoyez le verre avec un savon doux.
- Página 4 Vuelva a conectar la alimentación del circuito en el disyuntor o la caja de fusibles. ADVERTENCIA: Para atenuar este dispositivo, solo se pueden empelar dispositivos de atenuación compatibles según se describe en la hoja de especificaciones técnicas. Visite www.kohler.com para consultar la hoja de especificaciones técnicas. LIMPIEZA Limpie el elemento fijo SOLAMENTE con un paño suave y seco.