DeWalt D28730 Traducido De Las Instrucciones Originales página 26

EngLIsh
OPERATION
Instructions for Use

WARNING: Always observe the safety instructions and
applicable regulations.

WARNING: To reduce the risk of serious personal
injury, turn tool off and disconnect tool from power
source before making any adjustments or removing/
installing attachments or accessories. Be sure the
trigger switch is in the OFF position. An accidental start-up
can cause injury.
Proper Hand Position (Fig. A)

WARNING: To reduce the risk of serious personal injury,
Always use proper hand position as shown.

WARNING: To reduce the risk of serious personal injury,
always hold securely in anticipation of a sudden reaction.
Proper hand position requires one hand on the operating
handle 17 .
To Carry (Fig. A)
Fold down unit to position where you can carry the saw. Push in
the lock pin 1 to lock the arm down. Always carry the saw using
the carrying handle 19 .
Unlocking (Fig. A)
To unlock tool and raise head, depress motor arm slightly and
pull lock pin 1 out. Motor arm will then pivot upward.
Mounting (Fig. A)

CAUTION: Tool must be supported on stable, level,
non-skid surface to prevent unexpected movement
when operating.
1. Drill holes through the work surface that align the base of
the chop saw.
2. Insert two M10 bolts down through the mounting holes
in the base and through holes in mounting surface. The
approximate length of the screws should be the thickness of
the mounting surface plus 102 mm.
Spark Deflector Adjustment (Fig. A)

WARNING: Do not touch the spark deflector during or
immediately after operation as it becomes hot and may
cause skin burn.
To best deflect sparks away from surrounding persons and
materials, loosen the spark deflector screw
deflector 3 and then retighten screw. Do not allow cordset to
come into contact with deflector or sparks as damage to cordset
may occur.
Lock-Off Trigger Switch (Fig. A)
To turn the saw on, push the lock-off lever
then depress the lock-off trigger switch
while the switch is depressed. Allow the blade to spin up to
full operating speed before making the cut. To turn the saw
off, release the switch. Keep hands and material away from the
wheel until it has coasted to a stop. Allow the blade to stop
24
before raising the saw head. There is no provision for locking the
switch on.
Material Clamping and Supporting (Fig. B, C)
•
•
•
Vise Operation (Fig. A, D)
The vise has a quick travel feature. To release the vise
it is clamped tightly, turn the crank
two times to remove clamping pressure. Lift the vise lever
up. Pull crank assembly out as far as desired. The vise may
be shoved into work without cranking. Lower vise lever then
tighten vise on work by using crank.
Fence Operation (Fig. A, D, E)

The fence
cutting angle and to change spacing between the fence
and vise.
To Change the Desired Cutting Angle
Use the 8 mm hex key
the two fence bolts
with the slot line
bolts before use. For more accurate square cuts, disconnect the
power supply, loosen the two fence bolts, push arm down until
wheel extends into base. Place a square against the wheel and
16 adjust fence against the square. Securely tighten both fence
bolts before use. When making a miter cut, the vise
clamp securely, depending on the thickness of the workpiece
and the miter angle. Other aids (such as spring, bar or C-clamps)
will be necessary to secure the workpiece to the fence when
making these cuts.
Removal and Installation of Wheels
(Fig. F, G)

2 , adjust the spark

to the left,
14
13 . The saw will run

Angles are best clamped and cut with both legs resting
against base.
A spacer block 29 slightly narrower than the workpiece
can be used to increase wheel utilization (Fig. B).
Long workpieces must be supported by a block be level with top of base (Fig. C). The cut-off end
be free to fall downward to avoid wheel binding.
WARNING: Turn off and unplug the tool before
making any adjustments or removing or installing
attachments or accessories. Be sure the trigger
switch is in the OFF position.
5 can be adjusted two ways: to change desired
7 provided to loosen (do not remove)
15 . Align the desired angle indicator line
28 in the base 4
WARNING: To reduce the risk of serious personal
injury, turn tool off and disconnect tool from power
source before making any adjustments or removing/
installing attachments or accessories. Do not make
any adjustment while the wheel is in motion. Do not
make any adjustment while chop saw is plugged into
power supply.
WARNING: Always use gloves when handling wheels.
WARNING: Do not impact the wheel, and do not use a
wheel that has been dropped or impacted. Do not use a
chipped, deformed or damaged wheel.
30
31 so it will 32 should
6 when
8 counterclockwise one or
9
. Securely tighten both fence
may not
6