Adjusting The Guard - Black+Decker KG1202 Traducción De Las Instrucciones Originales

ENGLISH
Secure the flange with the screws (10). Make sure that the
u
screws are fully tight and that the guard can be rotated.
Removing
Use a screwdriver to remove the screws (10).
u
Remove the flange (9), guard (6) and spring washer (8).
u
Store these parts carefully.
Warning! Never use the tool without the guard.

Adjusting the guard

The guard can be rotated 90°.
Rotate the guard as required.
u
Fitting the side handle
Screw the side handle (4) into one of the mounting holes
u
in the tool.
Warning! Always use the side handle.
Fitting and removing grinding or cutting discs
(fig. C - E)
Always use the correct type of disc for your application.
Always use discs with the correct diameter and bore size
(see technical data).
Fitting
Fit the guard as described above.
u
Place the inner flange (11) onto the spindle (7) as shown
u
(fig. C). Make sure that the flange is correctly located on
the flat sides of the spindle.
Place the disc (12) onto the spindle (7) as shown (fig. C).
u
If the disc has a raised centre (13), make sure that the
raised centre faces the inner flange.
Make sure that the disc locates correctly on the inner flange.
u
Place the outer flange (14) onto the spindle. When fitting
u
a grinding disc, the raised centre on the outer flange must
face towards the disc (A in fig. D). When fitting a cutting
disc, the raised centre on the outer flange must face away
from the disc (B in fig. D).
Keep the spindle lock (5) depressed and tighten the outer
u
flange using the two-pin spanner (15) (fig. E).
Removing
Keep the spindle lock (5) depressed and loosen the outer
u
flange (14) using the two-pin spanner (15) (fig. E).
Remove the outer flange (14) and the disc (12).
u
Use
Warning! Let the tool work at its own pace. Do not overload.
Carefully guide the cable in order to avoid accidentally
u
cutting it.
Be prepared for a stream of sparks when the grinding or
u
cutting disc touches the workpiece.
8
(Original instructions)
Always position the tool in such a way that the guard
u
provides optimum protection from the grinding or cutting
disc.
Switching on and off
To switch the tool on, press the lock-off button (2) and
u
subsequently press the on/off switch (1).
For continuous operation, press the lock-on button (3) and
u
release the on/off switch.
To switch the tool off, release the on/off switch. To switch
u
the tool off in continuous operation, press the on/off switch
once more and release it.
Warning! Do not switch the tool off while under load.
Soft Start Feature
The soft start feature allows a slow speed build-up to avoid an
initial jerk when starting. This feature is particularly useful
when working in confined spaces.
No-Volt
The No-volt function stops the grinder restarting without the
switch being cycled if there is a break in the power supply.
Hints for optimum use
Firmly hold the tool with one hand around the side handle
u
and the other hand around the main handle.
When grinding, always maintain an angle of approx. 15°
u
between the disc and the workpiece surface.
Maintenance
Your BLACK+DECKER corded/cordless appliance/tool has
been designed to operate over a long period of time with a
minimum of maintenance. Continuous satisfactory operation
depends upon proper tool care and regular cleaning.
Warning! Before performing any maintenance on corded/
cordless power tools:
Switch off and unplug the appliance/tool.
u
Or switch off and remove the battery from the appliance/
u
tool if the appliance/tool has a separate battery pack,
Or run the battery down completely if it is integral and then
u
switch off.
Unplug the charger before cleaning it. Your charger does
u
not require any maintenance apart from regular cleaning.
Regularly clean the ventilation slots in you appliance/tool/
u
charger using a soft brush or dry cloth.
Regularly clean the motor housing using a damp cloth.
u
Do not use any abrasive or solvent-based cleaner.
Regularly open the chuck and tap it to remove any dust
u
from the interior (when fitted).