Sammic SL-360 Instrucciones página 8

4. Wait until the display stops showing the
model number and shows a temperature.
5. Now press button (Fig. B-2) on the electronic
board until all three 'Select Cycle' LEDs (Fig.
A-d, e, f) turn on simultaneously.
6. Use the pushbutton "Start Cycle" (Fig. A-4) to
increase the model number.
7. Push button "Drain" (Fig. A-5) to decrease
the model number.
8. After selecting the desired model number, press
button "Select Cycle" (Fig. A-3) to confirm. The
three "Select Cycle" LEDs (Fig. A-d, e, f) turn off
when the model number has been saved.
9. Power the machine down.
10. Set the two "Disconnect Elements" micros-
witches (Fig. B-1) to position OFF"
11. Power the machine up: the display shows
the selected model number.
OPERATION
Start-up
1.Open the 3/4" stopcock to allow water to enter
the machine.
2. Turn on the magnetothermal switch that pro-
tects the installation.
3. Check that the filters and the drain plug are in
place, as Figure "C" shows.
4. Turn the main switch (Fig. A-1) to the ON
position for the automatic filling of the wash
tank and the connection of the heater ele-
ments.
5. The light indicator (Fig.A-c) turns on when
the washing temperature (55º/ 60ºC) has
been reached.
6. Start Cycle:
- Place the objects to be washed in a basket
(rack).
- Close the door.
- Select the washing programme by pressing
the button (Fig. A-3) according to the soiling
level. The associated red LED will turn on.
- Press the Start Cycle key (Fig. A-4). The was-
hing phase indicator light (Fig. A-g) turns on.
The machine completes the entire washing
cycle. If you press the Start Cycle key (Fig. A-
5) again during the washing phase, the pro-
gramme immediately shifts to the rinsing pro-
cess. Pressing the said key during the rinsing
phase causes the machine to stop.
On models "B" with a drain pump, the machi-
ne performs a draining cycle at the end of the
washing phase priot to rinsing. The associa-
ted LED (j) will then turn on.
7. When the complete cycle has finished, the
two indicators (Fig. A-g) and (Fig. A-h) flash.
8. Models with a drain pump: With the door
open, press key (Fig. A-5) to start the drain
pump for a given period of time, which is long
8
EN
enough to empty the tub. At the end of this
time, the pump stops. Press the "Drain" key
(Fig. A-5) to alternately start and stop the
pump. With the drain plug, any residual water
will be removed from the tub.
Detergent dispenser
The glasswasher is prepared for its fitting with an
adjustable detergent dispenser, the part number
of which appears on the spare parts list. This dis-
penser has to be installed in the machine base, at
the front, as shown on the exploded view. At the
rear of the wash tank, there is an opening where
to insert the detergent injection nozzle.
The dispenser delivers about 0.7ml/s of deter-
gent (maximum). At the first filling of the tank,
feeding of detergent is roughly 119ml in 170s,
resulting in a maximum concentration of 3ml/l.
At each cycle, the dispenser delivers 10ml of
detergent. It is possible to reduce or increase
the injected quantity by turning the adjusting
screw on the dispenser.
Rinsing aid dispenser
Verify that the rinsing aid reservoir is full. Start
and stop the washing water pump 5 or 6 times
by pressing "Start Cycle" (Fig. A-4) and check
whether the tube fills up with rinsing aid and
goes in the boiler. Setting the dispenser is done
by turning an adjusting screw on the front lower
panel in the direction shown on the panel graph.
In order to determine whether the amount of rin-
sing aid is adequate, look at the glasses against
the light. If there are water droplets on the
glass, the amount of rinsing aid is insufficient; if
streaks develop, the quantity of rinsing aid is
too much.
Set of top filters
To guarantee proper cleanliness in installations
where intensive work is carried out, a set of top
filters can be installed as an accessory (code
indicated in the exploded view). All that has to
be done is to attach, with some screws, the rod
support in the holes made in the basket rails as
shown in figure 3.
The filters are placed on the supports.
Machine Draining
Models with no drain pump: Open the door and
take out the drain plug, leaving the filters in
place. Water will fall by gravity, dirt accumula-
ting in the filters.
Models "B" fitted with a drain pump:
· Open the door and take out the drain plug, lea-
ving the filters in place.
· Press the drain key (Fig. A-5) as specified on
the control panel, with the door open. The
drain pump operates during the programmed
time at the end of which it stops automatically.
By pressing the key, you can successively
start and stop the pump.
· Put the overflow drain plug and filters in place
again.
· Turn the main switch off and close the door.
Water softener. Setting water hardness.
You need to set the water hardness value on
the electronic board. The machine signals that
resin regeneration is needed by means of a
flashing "Regenerate" LED (Fig. A-k). This war-
ning signal depends on the number of rinsing
cycles done and the selected water hardness.
Therefore:
1. With the machine on and idle and both
"Disconnect Resistors" microswitches (Fig.
B-1) set to OFF, press the button (Fig. B-2)
on the electronic board.
2. One of the three "cycle duration" indicators
lights up (Fig. A, d, e or f). Depending on how
hard the water is the regeneration warnings
are activated:
W Nº
ATER HARDNESS OF EQUIVALENT
( .)
AT THE INLET CYCLES APPROX
30º F 90
40º F 70
50º F 50
3. Press "Start cycle" (Fig. A-4) and "Drain" (Fig. A-
5) - the LEDs will turn on successively - until you
have the required water hardness selected.
4. Press "Select cycle" (Fig. A-3) to save the
water hardness value. The LED flashes to
confirm correct saving.
5. Switch machine off.
Water softener. Regeneration Cycle.
The machine signals that resin regeneration is
needed by means of a flashing "Regenerate"
LED (Fig. A-k). If you think it proper, you can per-
form a regeneration cycle before the machine
warns you to do so. In this event, do as follows:
1. Drain the wash tank completely. MACHINE
EMPTY WITHOUT DRAIN PLUG.
2. With the door open, press "Select Cycle" (Fig.
A-3), the "Regeneration" LED (Fig. A-k) turns
on, meaning the machine is ready for the water
softener regeneration cycle.
3. Close the door and press "Start cycle" (Fig.
A-4) to start the regeneration cycle.
4. The display shows the number of rinsing
cycles done and letters "rn" (flashing). The
I
NDICATOR LIGHT
SHORT CYCLE
ON
MEDIUM CYCLE
ON
LONG CYCLE
ON