Sharp 26SL72 Manual De Operación página 31

Operation of Remote Control (Continued)
L HOW TO IDENTIFY A CABLE CONVERTER
L To Identify Your Cable Converter –Direct
Entry Method.
Use the following steps and list to quickly find
the remote control code for your cable TV
converter.
• First look up your converter's remote code
number before going through the direct code
entry steps below.
• If this procedure does not identify your
conver ter, use the Search method for
identification.
(1) Slide CATV /DVD-TV/VCR switch to CATV.
(2) Press and hold down DISPLAY and CH
DOWN ( 9 ) on your remote control.
Then release both buttons.
(3) Within ten seconds after releasing DISPLAY
and CH DOWN ( 9 ) , enter your converter's two-
digit code number using REMOTE KEYPAD
(refer to list).
• The remote control is now ready to send
commands to your converter.
• Some brands have more than one remote code
listed due to changes in the remote codes from
early to later model years. In such cases, you
may have to try more than one code to find
the code your converter accepts.
Note:
Depending on the model, year produced,
brand, and type of CATV converter, some
models may not be compatible with the remote
control.
L To Identify Your Cable Converter – Search
Method.
(1) Slide the CATV /DVD-TV/VCR switch to CATV.
(2) Press the POWER button on the cable
converter to ON.
(3) Stand at least six feet away from the converter.
Point the remote towards the converter.
Hold down the DISPLAY and CH UP ( 8 ) at
the same time. KEEP HOLDING THE
BUTTONS DOWN.
(4) Watch the Channel Number indicator on the
converter.
Channel numbers will scan up when the
converter has been identified.
Release the DISPLAY and CH UP ( 8 ) as soon
as the channel numbers start to scan up.
The converter's remote control code number
has been identified, and the remote is ready
to operate the converter.
25-34 26SL72/29SL82[E].p6.5e
CATV CONVERTER
BRAND
Anvision
Cable Star
Eagle
General Instrument
Jerrold
Magnavox
Oak Sigma
Panasonic
Philips
Pioneer
Randtek
RCA
Scientific Atlanta
Sony
Viewstar
Zenith
TIPS ON IDENTIFYING YOUR CABLE
CONVERTER:
Be Patient: a minute or two can seem a lot
longer when you're waiting for something to
happen, but the code should be identified
within 2 minutes. Remember, it is only a one-
time set-up.
Be careful not to let the CATV converter scan
more than five channels when the indicator
starts to move up. If you continue holding down
the DISPLAY and CH UP ( 8 ) after five channel
scans, the proper remote code can be passed
up, and the two minutes identify cycle will have
to be repeated.
If a channel change does not occur on the
cable converter within two minute, read the
identifying instructions again and repeat the
steps. Should a channel change still not occur,
the remote will not operate with the desired
converter.
Note:
Some satellite receivers can be operated by
the REMOTE CONTROL. If you have a
Satellite Receiver, you can use the above
method to search for available channels.
31
REMOTE CONTROL
CODE NUMBER
07, 08
07, 08
08
04, 05, 15, 23, 24, 25,
30, 36
04, 05, 15, 23, 24, 25
30, 36
07, 08, 19, 25, 28, 29,
32, 33, 40, 41
18
27, 39
07, 08, 19, 26, 28, 29,
32, 33, 40, 41
18, 20
07, 08
27, 43
03, 22, 42
44
07, 08, 19, 26, 28, 29
32, 33, 40, 41
14
4/25/01, 12:06 PM
31