Safety Notes; Important Notes; Functions; Information About Operation - LGB 23530 Manual Del Usario

Safety Notes

• This model may only be used with the operating system designed for it.
• Use only switched mode power supply units and transformers that are designed
for your local power system.
• This locomotive must never be supplied with power from more than one power pack.
• Pay close attention to the safety notes in the instructions for your operating system.
• Not for children under the age of 15.
• WARNING! Sharp edges and points required for operation.

Important Notes

• The operating instructions are a component part of the product and must therefore
be kept in a safe place as well as included with the product, if the latter is given to
someone else.
• The warranty card included with this product specifies the warranty conditions.
• Please see your authorized LGB dealer for repairs or spare parts.
• Disposing: www.maerklin.com/en/imprint.html
• Several parts are only included loose for protection during transport. These parts can
be cemented in place before operating the locomotive for the first time (Figure 3+4).
• This model is designed for track curves down to R1. However, we do recommend
using larger radii for operation.
• The front coupler included with the model can only be used for track curves larger
than R1.
• The loud running noises compared to other models lighter in weight are normal.

Functions

• This model is designed for operation on LGB two-rail DC systems with conventio-
nal LGB DC train controllers or power packs (DC, 0 – 24 volts).
• Factory-installed multiple protocol decoder (DC, DCC, mfx).
• The model is programmed with locomotive address 03 for use with the LGB Multi
Train System (DCC). The locomotive is automatically recognized in operation with mfx.
• Steam exhaust synchronized with the wheels
• Mfx technology for the Mobile Station/Central Station.
Name set at the factory: RhB G 45 114
• The functions can be activated only in parallel. Serial activation of the functions is
not possible (Please note here the instructions for your controller).
General Note to Avoid Electromagnetic Interference:
A permanent, flawless wheel-rail contact is required in order to guarantee operation
for which a model is designed. Do not make any changes to current-conducting parts.
Mode of Operation Switch
The model has a mode of operation switch on the underside of the tender (Figure 1).
Pos. 0 Locomotive stored without current
Pos. 1 Locomotive ready for operation
Smoke Unit
In analog operation, the smoke generator synchronized to the wheels is turned off
due to its power draw. This can be turned on by setting CV 13 from Value 32 to Value
96, but this may affect the running characteristics when running very slowly – depen-
ding on the current supply.
The smoke generator may be filled with a maximum of 5 – 6 milliliters / 0.2 fluid
ounces of 2421 smoke fluid.
Sound
The volume of the electronic sounds can be changed with the controller on the
underside of the tender (Figure 2).
The whistle can be activated with the LGB sound activation magnet (item no. 17050)
that is included with the locomotive. The activation magnet can be clipped into place
between the ties of most LGB track sections. Place the magnet on the right side in or-
der to activate the short whistle blast when the locomotive passes over this location.
The long whistle blast will sound when the magnet is placed on the left side.

Multi-Protocol Operation

Analog Operation
This decoder can also be operated on analog layouts or areas of track that are
analog. The decoder recognizes alternating current (DC) and automatically adapts
to the analog track voltage. All functions that were set under mfx or DCC for analog
operation are active (see Digital Operation).
The built-in sound functions come from the factory inactive for analog operation.
Digital Operation
The decoders are multi-protocol decoders. These decoders can be used under the
following digital protocols: mfx or DCC.
The digital protocol with the most possibilities is the highest order digital protocol.
The sequence of digital protocols in descending order is:
Priority 1: mfx; Priority 2: DCC; Priority 3: DC
Note: Digital protocols can influence each other. For trouble-free operation, we re-
commend deactivating those digital protocols not needed by using CV 50. Deactivate
unneeded digital protocols at this CV if your controller supports this function.
If two or more digital protocols are recognized in the track, the decoder automatically
takes on the highest order digital protocol, example: mfx/DCC; the decoder takes on
8