Checklist For Taking A Reliable Measurement; Taking A Blood Pressure Measurement; How Not To Store A Reading; How Do I Evaluate My Blood Pressure - Microlife BP A7 Touch BT Manual Del Usuario

 Do not remove the cuff between measurements.
 If one of the individual measurements was questionable, a fourth
one is automatically taken.

AF detection is only activated in AFIB/MAM mode.

3. Checklist for Taking a Reliable Measurement

Avoid activity, eating or smoking immediately before the

measurement.
Sit down on a back-supported chair and relax for 5 minutes.

Keep the feet flat on the floor and do not cross your legs.
Always measure on the same arm (normally left). It is recom-

mended that doctors perform double arm measurements on a
patients first visit in order to determine which arm to measure in
the future. The arm with the higher blood pressure should be
measured.
Remove close-fitting garments from the upper arm. To avoid

constriction, shirt sleeves should not be rolled up - they do not
interfere with the cuff if they are laid flat.
Always ensure that the correct cuff size is used (marking on the

cuff).
 Fit the cuff closely, but not too tight.
 Make sure that the cuff is positioned 1-2 cm above the elbow.
 The artery mark on the cuff (ca. 3 cm long bar) must lie over
the artery which runs down the inner side of the arm.
 Support your arm so it is relaxed.
 Ensure that the cuff is at the same height as your heart.

4. Taking a Blood Pressure Measurement

1. Slide the lock switch 3 down to the «unlock» position.
2. Select standard (single measurement) or AFIB/MAM mode
(automatic triple measurement): see details in chapter «2.».
3. Press the START/STOP button AN to start the measurement.
4. The cuff will now pump up automatically. Relax, do not move
and do not tense your arm muscles until the measurement
result is displayed. Breathe normally and do not talk.
5. When the correct pressure is reached, the pumping stops and the
pressure falls gradually. If the required pressure was not reached,
the device will automatically pump some more air into the cuff.
6. During the measurement, the pulse indicator BR flashes in the
display.
4
7. The result, comprising the systolic AP and the diastolic AQ blood
pressure and the pulse rate AR is displayed. Note also the
explanations on further display symbols in this booklet.
8. When the device has finished measuring, remove the cuff.
9. Switch off the device. (The monitor does switch off automatically
after approx. 1 min.).

AF detection is only activated in AFIB/MAM mode.

You can stop the measurement at any time by pressing the
START/STOP button (e.g. if you feel uneasy or an
unpleasant pressure sensation).

This monitor is specially tested for use in pregnancy and
pre-eclampsia. When you detect unusual high readings in
pregnancy, you should measure after a short while again
(eg. 1 hour). If the reading is still too high, consult your
doctor or gynecologist.
In pregnancy the AFIB symbol can be ignored.

How not to store a reading

As soon as the reading is displayed press and hold the START/
STOP button AN until «M» AO is flashing. Confirm to delete the
reading by pressing the M-button AO.

«CL» is displayed when the reading is deleted from the
memory successfully.

How do I evaluate my blood pressure?

The LED traffic light indicator on the left-hand side of the display BP
indicates within which range the measured blood pressure lies. The
value is either within the optimum (green), elevated (yellow) or high
(red) range. The classification corresponds to the following ranges
defined by international guidelines (ESH, ESC, JSH). Data in mmHg.
Range Systolic Diastolic Recommendation
1. blood pressure ≥135
too high
2. blood pressure 130 - 134 80 - 84
elevated
3. blood pressure <130
normal
The higher value is the one that determines the evaluation. Example: a blood pressure value of 140/80 mmHg or a value of
130/90 mmHg indicates «blood pressure too high».
≥85 Seek medical
advice
Self-check
<80 Self-check