Preparation For Use; Basic Functions; Fm Radio Operation - Sharp XL-B517D Manual Del Usuario

6
29. LOUD: Press to increase the level of bass at low volume levels.
30. NUMBER (0-9): Use to select songs, presets or enter frequency.
31. SAVE: Press to save your favourite stations.
Fitting or replacing the remote control batteries
1.
To open the battery compartment, push your thumb down on to
the circle on the battery compartment cover and slide it down.
2. Fit two AAA batteries observing polarity +/- as shown. When
replacing the batteries, use only the same type of battery supplied.
3.
Re- t the battery cover and clip it in place.

Preparation for use

3
4
7
5
AUX IN
1.
Place a speaker on either side of the main unit, preferably at the same
height and with at least 150mm space between each speaker to the
main unit.
Connect the speaker plugs to the rear of the unit. Take care to match
the speaker placed to the LEFT to the LEFT output on the rear of the
unit. Repeat for the RIGHT speaker.
2.
Please ensure that the voltage marked on the rating label,
located on the rear panel, is the same as the voltage in your area.
Insert the power lead in to the AC IN socket on the back of the
unit. Plug the other end of the cable in to the wall socket.
3. Press the STANDBY button on the main unit to turn it ON.
Extend the ANTENNA to get the best reception. Press the
button on the unit, or DAB/FM button on the remote
control to enter the DAB/FM mode. To use the radio in
DAB/FM mode, follow the instructions in the FM or DAB
RADIO OPERATION chapter of the User Manual.
4. Press the button on the unit, or CD button on the remote
control to enter the CD mode. Press the
the disc drawer and insert a disc. Press the
to close. The CD will begin playing from the rst track.
5. button on the unit, or AUX button on the
Press the
remote control to enter the Aux In (Audio) mode. Connect
1
6
AUDIO IN
button to open
button again
your audio device to the AUX IN socket via a 3.5mm aux in
cable. Control playback via your connected audio device.
6. Press the button on the unit, or
control button to enter the Bluetooth mode. Activate the
Bluetooth enabled device and select the "SHARP XL-B517D".
Select the song you want and press to play.
7. button on the unit, or USB button on the remote control
Press the
to enter the USB mode. Plug the USB device to USB port on the front
panel of the unit, and it will read the USB and play automatically.

BASIC FUNCTIONS

Setting the time/date
1. To set the time/date manually, long press the MENU
button when the unit is in standby. Use the
to change the values and press
2. To set the time/date automatically, press the MENU button when the
unit is on. Select the SYSTEM menu and press
TIME from the SYSTEM menu and then AUTO UPDATE where you
will be able to select the source of the update. Press MENU to exit.
2
Switching modes
To switch between the modes: DAB+, FM, CD, Bluetooth, USB and AUX IN,
press SOURCE button on the unit or the corresponding button (DAB/FM,
CD, , AUX/USB) on the remote control.
Volume control
1. Increase: Rotate the VOLUME control on the main unit
clockwise or press the VOL+ button on the remote.
2. Decrease: Rotate the VOLUME control on the main unit
anti-clockwise or press the VOL- button on the remote.
EQ eff ects
Press the EQ button on the remote repeatedly to cycle through a set of
equaliser presets to adjust the sound. Choose from CLASSIC, ROCK, POP,
JAZZ, DANCE, LIVE and O .
Loudness function
This function will increase the level of bass at low volume levels. Press the
LOUD button on remote to enable the e ect. Press again to disable the
e ect.
Mute function
Press the button at any time to mute the sound output. Press again to
unmute.
Tone controls
To adjust the bass, use the BAS+ or BAS- buttons on the remote control.
To adjust the treble, use the TRE+ or TRE- buttons on the remote control.
Standby mode
Press the STANDBY button on the unit or the remote to put the system
into standby mode. To resume normal operation, press this button again.
NOTE: This unit is designed to enter STANDBY mode automatically, after about
15 minutes (approximately) of inactivity. Press STANDBY button to wake the
unit.
NOTE: When you power on the unit from standby, it will resume in the mode
that was last used.

FM radio operation

1. Press the source button
DAB/FM button on the remote control twice to enter
FM mode. (FM frequency: 87.50-108.00MHz)
2. Press the / buttons on remote control to decrease
or increase the frequency in 0.05MHz increments.
button on the remote
/ keys
to con rm.
to con rm. Select
on the unit, or