Step 3. Convert To Lp Gas (Optional); Step 4. Install The Anti-Tip Device; Step 5. Plug In And Place - Samsung nx60a6511ss Manual De Instalación

Step 3. Convert to lp gas (optional)

All new gas ranges are shipped from the factory set up to use natural gas. Any
Samsung gas range can be converted to use LP gas. Refer to page 55 in the User
Manual to contact a qualified service technician.
The conversion process should only be performed by a qualified LP gas installer.
Conversion instructions and LP orifices will be supplied with the LP conversion kit.
The conversion to LP requires all burner orifices to be changed (5 surface burners
and 2 oven burners).
In addition, the nozzle on the gas pressure regulator needs to be reversed. All
replaced orifices must be left with the consumer, including the instructions and
retrofit sizes and orifice indication.
Checking the flame quality all burner after converting to lp gas.

Step 4. Install the anti-tip device

WARNING
To reduce the risk of tipping, the appliance must be secured by properly installing
the anti-tip device packed with the appliance.
• All ranges can tip, resulting in personal injury.
• Tipping ranges can cause burns from spills, personal injury, and/or death.
• To prevent accidental tipping, install and check the anti-tip bracket following the
instructions and template supplied with the bracket.
Install_NX60A6_DG68-01337A-00_EN+MES+CFR.indb 19 Install_NX60A6_DG68-01337A-00_EN+MES+CFR.indb 19
An anti-tip bracket and screws, installation
instructions, and template are shipped
with every range (PN DG94-00870B). The
instructions include information necessary
to complete the installation of the anti-tip
bracket. Read and follow the instructions on
the sheet and use the template for anti-tip
bracket installation. If not properly installed,
the range could be tipped by you or a child
standing, sitting, or leaning on an open oven
door.
Anti-Tip
bracket
*approximately
21 / " (16.5 mm)
32
Screw must enter
wood or concrete
To check if the bracket is installed and engaged properly, remove storage drawer
and look underneath the range to see that the leveling leg is engaged in the
bracket. Carefully tip the range forward. The bracket should stop the range within
4 inches (10.2 cm) of tipping. If it does not, the bracket must be reinstalled.
If the range is pulled from the wall for any reason, always repeat this procedure
to verify the range is properly secured by the anti-tip bracket. Never completely
remove the leveling legs or the range will not be secured to the anti-tip device
properly.

Step 5. Plug in and place

WARNING
BEFORE OPERATING OR TESTING, follow the grounding requirements on pages 17
~ 18 in this manual. Improper connection of the grounding plug can result in a risk
of electric shock.
• All gas ranges come with a power cord. The power cord is connected to the rear
of the range. Please review "Electrical requirements" on pages 17 ~ 18.
• The electrical system, including the power cord, is preinstalled and prewired at
the factory. Altering any part of this system may result in a short or overload.
1. Plug in the power cord. Make sure the outlet meets local or national electrical
codes as referenced on pages 17 ~ 18.
2. Slide the range into place.
3. Check the gas supply line to make sure it did not get damaged and it stayed
connected during positioning.
4. Check to make sure the back leg of the range has slid into the anti-tip bracket.
Carefully tip the range forward to ensure that the anti-tip bracket engages the
back brace and prevents tip-over.
*NOTE: To install the Anti-Tip
bracket, release the leveling
leg. A minimum clearance of
/ " (16.5 mm) is required
21
32
between the range bottom
and the kitchen floor.
English 19
2020-12-30 2020-12-30 10:56:13 10:56:13