AneX Cross Manual De Uso página 29

STROLLER
ASSEMBLING / DISASSEMBLING
Unbox this stroller's frame and put it horizontally on
the floor (fig. 1). Disable the lock against accidental
unfolding (fig. 2).While holding the handle pull upwards
vigorously to fix the system (you should hear a specific
sound) (fig. 3, 4). To fold the frame press and hold the
red button, located on the frame`s right lever. Then
simultaneously pull the levers, located on both sides of
the frame (fig. 5). Slightly pull the frame up to the original
position (same when packed) (fig. 1).
HANDLE HEIGHT ADJUSTMENT
Simultaneously press the round buttons, placed
parallel on both sides of the handle. Set comfortable
handle height for you (fig. 6).
WHEEL MOUNTING / DISMOUNTING
Before mounting a wheel, insert an axle, while holding the
red button (fig. 7). Release the button to fix the axle
(you should hear a specific sound). To mount a wheel, press
its center button, then mount wheels on an axle till it stops,
release button and slightly pull until it locks (fig. 8). To
dismount a wheel, press at its midpoint and pull along the
axle till its final removal (fig. 8). A wheel can be removed
without axle, but the axle can be removed by pressing
the red button (fig.7).
FRONT SWIVEL WHEELS
DISMOUNTING AND LOCKING
The stroller`s frame is equipped with two front swivel
wheels, which rotate 360° on its axle. To dismount
front wheel press vertically the button located above
this wheel. A wheel can be dismounted together with
the axle (fig.9). To secure the rotary wheels system,
turn the regulator located below the dismounting
button (fig. 10).
BRAKE
The stroller is equipped with parking brakes, which
block its rear wheels (fig. 11). To stop the stroller you
need to press rear wheels blocking pedal (fig. 11).To
continue moving, you need to reset the pedal (fig.11).
PRE-USE PROCEDURES
SHOCK ABSORPTION
The stroller has a steel-ring shock absorption system and
frame shock absorption that let your child feel comfortable.
(fig.12). Spring shock absorption mechanism is regulated by
a special switch, which is located under the shock absorber
(fig. 12). Always adjust both sides equally.
PORTABLE CRADLE MOUNTING /
DISMOUNTING
To mount the portable cradle, place the adapters into the
adapter pockets, located on the frame's inner side (fig. 13).
The portable cradle adapters are blocked automatically.
To dismount the portable cradle, press the buttons of the
portable cradle adapters, while lifting it up (fig. 13).
If necessary, the portable cradle's inner part can be removed
and washed (fig.14, 15). The portable cradle`s backrest
(covered by a coconut mattress) can be adjusted to the
desired height with the help of regulator, which is located on
the bottom side of the cradle (fig. 16). To adjust the cradle`s
backrest push the regulator and scroll to the desired height.
PORTABLE CRADLE HOOD, FEET COVER
The portable cradle is equipped with the folding hood
that protects a child from natural phenomena (wind,
sun, snow, rain). The stroller's hood position is adjusted
with buttons at the bottom of the hood (fig.17). Cradle is
equipped with the additional handle for its transportation
(fig. 18). Cradle is equipped with the feet cover, which puts
on at the front of the cradle and is fixed with buttons on
both sides (fig. 19). In order to fix the canopy, pull it towards
yourself (You will hear distinctive sound). The portable
cradle's hood can be ventilated by unfastening a zipper at
the bottom part of the hood and bending it down
(fig. 20). The stroller has an insect protection which is
suitable both for cradle and seat unit (fig. 21). The stroller has
a rain protection which is suitable both for cradle and seat
unit (fig. 23, 24). The cradle is ventilated (fig.22). Turn the
lever counterclockwise to open the ventilation and clockwise
to close it (fig. 22).
SEAT UNIT MOUNTING / DISMOUNTING
To mount the seat unit, place its adapters into the adapter
pockets located on the frame's inner side (fig.25). The seat
EN