Idiomas disponibles
Idiomas disponibles
5
Affix hanger to wall (hand tighten only). Mount
lavatory for positioning, level the deck, and mark
bottom anchor screw holes (if applicable). Remove
lavatory, tighten the hanger positioning screws and
drill pilot holes for anchor screws and 4 mounting
screws. Install and tighten the mounting screws.
Steel Hanger
Mounting Screw
Positioning Screw
Lavatory
7
Return the fitted lavatory to
the installed position. Connect
trap to drain assembly hand
tight to check alignment. It
may be necessary to cut off
part of the tailpiece (area "B")
or part of the horizontal leg of
the trap (area "C").
9
Installing Optional Shroud
Position semi-pedestal/shroud under basin
and secure to wall using 2" (51mm) screws.
FIGURE 2
SEMI-PEDESTAL/SHROUD*
ANCHOR HOLES
*SHROUD SOLD SEPARATELY
3-1/2"
(89mm)
FIGURE 3
8-1/2"
(216mm)
7-1/2"
10-1/2"
(191mm)
(267mm)
BARRIER FREE
WASTE
34" (864mm)
*33" (838mm)
*IN ONTARIO
FINISHED FLOOR
Anchor Screw
(if used)
C
B
If inspection of this AS America, Inc. ("American Standard") plumbing product, within one year
after its initial purchase, confirms that it is defective in materials or workmanship, American
Standard will repair or, at its option, exchange the product for a same or similar model.
This limited warranty applies only to the original purchaser and installation of these products. In
the event of a limited warranty claim, proof of purchase will be required—save sales receipts.
CONCEALED ARM
This limited warranty does not apply to local building code compliance. Since local building codes
CARRIER HOLES
vary considerably, the purchaser of this product should check with a local building or plumbing
contractor to ensure local code compliance before installation.
BASIN ANCHOR
This limited warranty will be void if the product has been moved from its initial place of
HOLES
installation; if it has been subjected to faulty maintenance, abuse, misuse, accident or other
damage; if it was not installed in accordance with American Standard's instructions; or if it has
SLOTS FOR
been modified in a manner inconsistent with the product as shipped by American Standard.
BASIN LEG BOLTS
American Standard's option to repair or exchange the product under this limited warranty does
not cover any labor or other costs of removal or installation including any costs of any
surrounding material such as tile or marble. American Standard is not responsible for any other
incidental or consequential damages attributed to a product defect or to the repair or exchange of
a defective product, all of which are expressly excluded from the warranty. This limited warranty
BEND FLEXIBLE
does not cover the extension beyond the duration of this limited warranty of any implied limited
SUPPLY
warranties, including those of merchantability or fitness for an intended purpose. (Some states or
TUBES
provinces do not allow the exclusion or limitation of implied warranties, so this exclusion may not
apply to you.)
This limited warranty gives you specific legal rights. You may have other statutory rights that vary
from state to state or from province to province, in which case this limited warranty does not
affect such statutory rights.
For service under this warranty, it is suggested that a claim be made through the contractor or
dealer from or through whom the product was purchased, or that a service request (including a
description of the product model and of the defect) be sent to the following address:
10"
(254mm)
Attention: Director of Consumer Affairs
For residents of the United States, warranty
information may also be obtained by calling
the following toll free number: (800) 442-1902
6
Following manufacturers instructions, install faucet
and drain assembly. (Not included). Be certain to
apply a bead of sealing putty on the underside of
the drain (Part "A") in order to ensure a watertight
seal between the lavatory and drain. Remove
excess putty after installing drain on lavatory.
8
Secure lavatory on
hanger as shown in 5.
Insert and tighten anchor
screws if applicable.
Connect hot and cold
supply lines to the
shut-off valves. Tighten
trap joints for watertight
assembly. Apply a bead
of caulk around the edge
which contacts the wall
as shown.
AS AMERICA, INC. ONE YEAR LIMITED WARRANTY
In the United States:
American Standard Brands,
1 Centennial Ave
Piscataway, New Jersey 08854
www.americanstandard.com
THIS WARRANTY IS NOT TRANSFERABLE
FROM ORIGINAL CONSUMER PURCHASER.
2
Caulk
In Canada:
Customer Service Manager
LIXIL Canada ULC
AS Maquila, S.A. de C.V.
5900 Avebury Road
Via Morelos #330
Mississauga, Ontario
Col. Santa Clara
Canada L5R 3M3
Ecatepec 55540 Edo. Mexico
Toll Free: (800) 387-0369
www.americanstandard.com.mx
www.americanstandard.ca
730427-100 Rev. 6 8/19
Shut-off
Valves
In Mexico:
