Maintenance And Cleaning; Verwendete Symbole - Dremel 3000 Traducción De Las Instrucciones Originales

or other suitable lubricant on the cutter to prevent the
cut material from adhering to the cutter teeth.
NOTE: Increasing pressure on the tool is not the answer
when it is not performing properly. Try a different accessory
or speed setting to achieve the desired result.

MAINTENANCE AND CLEANING

NO USER SERVICEABLE PARTS INSIDE (you can
!
only inspect and replace the carbon brushes
(3000/4300)). PREVENTIVE MAINTENANCE PERFORMED
BY UNAUTHORIZED PERSONNEL MAY RESULT IN
INCORRECT CONNECTION OF INTERNAL WIRING AND
COMPONENTS WHICH COULD CAUSE SERIOUS
HAZARD.
INSPECTING/REPLACING CARBON BRUSHES
(3000/4300)
A f
Inspect the brushes for wear every 40-50 hours of use.
Also inspect the brushes when the tool runs erratically,
loses power, or makes unusual noises.
Using the tool with worn brushes will permanently
damage the motor.
Use only original DREMEL replacement brushes.
1. Unplug the tool and place it on a clean surface.
2. Remove the two brush caps with the tool wrench as a
screwdriver.
3. Remove the two brushes from the tool by pulling the
springs that are attached.
4. Inspect both brushes. If a brush is less than 3mm
long and/or the surface of the brush is rough or pitted,
replace the carbon brush by a new one:
– remove the spring from the brush
– throw away the old brush and place the spring on
a new brush
5. Place the carbon brushes (with spring) back into the
tool (there is only one way the brush will fit back into
the tool).
6. Replace the brush caps by turning the caps clockwise
(to tighten, use the wrench - do not overtighten).
NOTE: If one brush is worn, you should replace both
brushes for better performance of the tool.
The tool can be cleaned most effectively with compressed
dry air. Always wear safety goggles when cleaning
tools with compressed air.
TO AVOID ACCIDENTS, ALWAYS DISCONNECT THE
!
TOOL AND/OR CHARGER FROM THE POWER
SUPPLY BEFORE CLEANING
Ventilation openings and switch levers must be kept clean
and free of foreign matter. Do not attempt to clean the tool
by inserting pointed objects through an opening.
CERTAIN CLEANING AGENTS AND SOLVENTS
!
DAMAGE PLASTIC PARTS. Some of these are:
gasoline, carbon tetrachloride, chlorinated cleaning solvents,
ammonia and household detergents that contain ammonia.
SERVICE AND WARRANTY
We recommend that all tool service be performed by a
Dremel Service Centre.
This Dremel product is guaranteed in accordance with
statutory/country-specific regulations; damage due to
normal wear and tear, overload or improper handling are
excluded from the warranty.
In case of a complaint, send the undismantled tool and/or
charger and proof of purchase to your dealer.
CONTACT DREMEL
For more information on service and warranty, the Dremel
product range, support and hotline, go to www.dremel.com.
NOISE AND VIBRATION
3000
Sound pressure level (standard deviation 3dB) dB(A) 77.1
Sound power level (standard deviation 3dB) dB(A)
Vibration (triax vector sum) m/s
Vibration uncertainty K m/s
4000
Sound pressure level (standard deviation 3dB) dB(A) 78.0
Sound power level (standard deviation 3dB) dB(A)
Vibration (triax vector sum) m/s
Vibration uncertainty K m/s
4300
Sound pressure level (standard deviation 3dB) dB(A) 74.4
Sound power level (standard deviation 3dB) dB(A)
Vibration (triax vector sum) m/s
Vibration uncertainty K m/s
NOTE: The declared vibration total value has been
measured in accordance with a standard test method and
may be used for comparing one tool with another. It may
also be used in a preliminary assessment of exposure.
The vibration emission during actual use of the power tool
can differ from the declared total value depending on the
ways in which you use the tool.
Make an estimation of the exposure in the actual
conditions of use and identify the safety measures for
personal protection accordingly (taking account of all parts
of the operating cycle such as the times when the tool is
switched off and when it is running idle in addition to the
trigger time).
The tool, accessories and packaging should be sorted for
environmental-friendly recycling.
ONLY FOR EC COUNTRIES
According the European Guideline 2012/19/EC for Waste
Electrical and Electronic Equipment and its implementation
into national right, power tools that are no longer usable
must be collected separately and disposed of in an
environmentally correct manner.

VERWENDETE SYMBOLE

1
LESEN SIE DIESE ANWEISUNGEN
2
TRAGEN SIE GEHÖRSCHUTZ
3
TRAGEN SIE AUGENSCHUTZ
4
TRAGEN SIE EINE STAUBMASKE
5
KLASSE-II-AUSFÜHRUNG
6
WERFEN SIE ELEKTROWERKZEUGE NICHT IN
DEN HAUSMÜLL
24
2
2
2
2
2
2
DISPOSAL
6
DE
88.1
12.8
1.5
89.0
11.4
1.5
85.4
9.0
1.5