SIOUX A Serie Instrucciones

SPW-440D-3, SPW-550D-3, SPW-660D-4, SPW-660D-40, SPW-770D-3, SPW-440-3,
SPW-550-3, SPW-660-4, SPW-770-3, SPW-880-4, SPW-990-3,
SPW-1110-1, SPW-1330-1, SPW-440S-1, SPW-550S-1, SPW-660S-1,
SPW-770S-1, SPW-440SD-1, SPW-550SD-1, SPW-660SD-1, SPW-770SC-1
READ AND UNDERSTAND "SAFETY INSTRUCTIONS FOR AIR TOOLS" PLUS THESE
INTENDED USE
This tool is intended to be used with power tool sockets, driving
adaptors or driver bits to tighten and loosen threaded fasteners. Do
not use this tool for any other purpose.
AIR SUPPLY
The efficiency of the tool is dependent on the proper supply of clean
dry air at 58 psig (4.0 bar) to 90 psig (6.2 bar). The use of an in-
line filter and pressure regulator will insure maximum output and tool
life. Before connecting tool, blow out the air line to remove water
and dirt which may have accumulated.
LUBRICATION
All Sioux Pulse Tool air motors are "Lubrication Free". They do not
require lubrication. However the addition of a quality air motor oil will
not hinder the performance of the tool.
HOSE AND HOSE CONNECTIONS
The supply hose I.D. should not be less then that listed in the
following chart. Do not use coupling or fitting with a smaller I.D. than
the supply hose. When using quick couplers, install a leader hose
between the tool and the quick coupler.
CATALOG NUMBER
SPW-440D-3 ........................................... 1/4" (6.3 mm)
SPW-550D-3 ........................................... 1/4" (6.3 mm)
SPW-660D-4 ........................................... 3/8" (9.5 mm)
SPW-660D-40 .......................................... 3/8" (9.5 mm)
SPW-770D-3 ........................................... 3/8" (9.5 mm)
SPW-440-3 ............................................ 1/4" (6.3 mm)
SPW-550-3 ............................................ 1/4" (6.3 mm)
SPW-660-4 ............................................ 3/8" (9.5 mm)
SPW-770-3 ............................................ 3/8" (9.5 mm)
SPW-880-4 ............................................ 3/8" (9.5 mm)
SPW-990-3 ............................................ 3/8" (9.5 mm)
SPW-1110-1 ........................................... 3/8" (9.5 mm)
SPW-1330-1 ........................................... 3/8" (9.5 mm)
SPW-440SD-1 ......................................... 1/4" (6.3 mm)
SPW-550SD-1 ......................................... 1/4" (6.3 mm)
SPW-660SD-1 ......................................... 3/8" (9.5 mm)
INSTRUCTIONS FOR SIOUX PNEUMATIC
PULSE WRENCHES
(STARTING WITH SERIAL "A")
INSTRUCTIONS BEFORE OPERATING THIS TOOL!
SAVE THESE INSTRUCTIONS!
HOSE SIZE
WARNING
SPW-440S-1 ........................................... 1/4" (6.3 mm)
SPW-550S-1 ........................................... 1/4" (6.3 mm)
SPW-660S-1 ........................................... 3/8" (9.5 mm)
SPW-770S-1 ........................................... 3/8" (9.5 mm)
SPW-770SC-1 ......................................... 3/8" (9.5 mm)
GENERAL OPERATION
Starting Tool
1. Make sure the socket or bit is securely attached to the tool.
2. Make sure the socket or bit is square with the head of the
fastener and the tool is in line with the socket.
3. Make sure the reversing control is set for the proper spindle
rotation.
4. Make sure your hands and fingers are away from the
fastener and socket or bit.
5. Depress trigger or lever to start tool.
Reversing Spindle Rotation
Do not change the rotation while the tool is running.
Pistol Grip Tools
The reverse lever is located on the left side of the tool. Place the
lever in the up position for right hand rotation, and in the down
position for left hand rotation,.
Straight and Angle Tools
The reverse control is located on the body of the tool. Rotate the
control in the clockwise direction for right hand rotation and in the
counterclockwise direction for left hand rotation.
IF THE TOOL LOOSES POWER, CHECK THE FOLLOWING:
• Air Pressure
Ensure that there is an adequate supply of clean, dry air at
58 psig (4.0 bar) to 90 psig (6.2 bar).
• Sockets
Check for loose, worn, or cracked sockets.
• Hose Size
Ensure that the hoses, couplers and fittings meet the criteria
specified in "HOSE AND HOSE CONNECTIONS" above.
• Dirt or Debris In Tool or Muffler
Clean tool or muffler as needed.
1
Form ZCE646
Date 2003July26/E
Page 1 of 16
Printed In U.S.A.