Safety Instructions; Description And Specifications; Piping Suction; Piping Discharge - Red Jacket XYLEM RSPA Instalación Operación Mantenimiento

Safety Instructions

Safety Instructions
TO AVOID SERIOUS OR FATAL PERSONAL
JURY OR MAJOR PROPERTY DAMAGE, READ AND
FOLLOW ALL SAFETY INSTRUCTIONS IN MANUAL
AND ON PUMP.
This is a SAFETY ALERT SYMBOL. When
you see this symbol on the pump or in the
manual, look for one of the following signal
words and be alert to the potential for per-
sonal injury or property damage.
Warns of hazards that WILL cause serious
DANGER
personal injury, death or major property
damage.
Warns of hazards that CAN cause serious
WARNING
personal injury, death or major property
damage.
Warns of hazards that CAN cause personal
CAUTION
injury or property damage.
NOTICE: Indicates special instructions which are very
important and must be followed.
THIS MANUAL IS INTENDED TO ASSIST IN THE
INSTALLATION AND OPERATION OF THIS UNIT
AND MUST BE KEPT WITH THE PUMP.
THOROUGHLY REVIEW ALL INSTRUCTIONS AND
WARNINGS PRIOR TO PERFORMING ANY WORK
ON THIS PUMP.
MAINTAIN ALL SAFETY DECALS.
NOTICE: INSPECT UNIT FOR DAMAGE AND
REPORT ALL DAMAGE TO THE CARRIER
OR DEALER IMMEDIATELY. DO NOT USE
PUMP IF DAMAGE IS SUSPECTED.
UNITS NOT DESIGNED FOR USE
WARNING
WITH HAZARDOUS LIQUIDS OR
FLAMMABLE GASES.
Hazardous fluids can
cause personal injury
or property damage.

Description and Specifications

Description and Specifications
•
The RJSP and RSPA are end suction, single stage,
self-priming centrifugal pumps for lawn sprinkling,
HVAC systems, and general water transfer.
•
Casing is cast iron construction with tapped openings
provided for vacuum gauge and casing drain.
Impellers are enclosed design, glass filled Noryl ™ ,
•
threaded directly on motor shaft.
•
Standard motors are NEMA standard, 3500 RPM, open
drip proof enclosure.
•
Maximum Liquid Temperature: 140ºF (60ºC)
•
Maximum Starts per Hour: 20 – evenly distributed
Piping
Piping
•
IN- Pump MUST be installed horizontally on a solid flat
surface, with discharge on top.
•
Allow adequate space for servicing and ventilation.
Protect the unit from weather and water damage due to
rain or flooding or freezing temperatures.
•
Piping should be no smaller than the suction and dis-
charge connections and kept short as possible, avoiding
unnecessary fittings to minimize friction losses.
•
All piping MUST be independently supported and
MUST NOT place any piping loads on the pump.
NOTICE: DO NOT FORCE PIPING INTO PLACE
AT PUMP SUCTION AND DISCHARGE
CONNECTIONS.
•
All pipe joints MUST be airtight.
The use of Teflon ™ tape, or equivalent, is recommended
•
for ALL pipe joints.
SUCTION
•
Total suction lift, including elevation and pipe friction
loss, should not exceed 25 feet of head.
•
Install an airtight union in the suction line close to the
pump. See Figure 1.
•
Installation of a foot valve at liquid source is recom-
mended.
NOTICE: FOR INSTALLATIONS WITH LONG
SUCTION PIPING, BOTH A FOOT VALVE
AND A CHECK VALVE ARE
RECOMMENDED.
•
To avoid air pockets, no part of the piping should be
above the pump suction connection and piping should
slope upward from liquid source.
•
For installations with long suction piping, fill the suction
pipe with water before connecting to pump.
DISCHARGE
•
Install a tee at the discharge connection of the pump.
The top opening of the tee is required for initial priming.
See Figure 1.
DISCONNECT SWITCH

Wiring and Grounding

Wiring and Grounding
WARNING
Hazardous voltage
can shock, burn or
cause death.
PRIMING OPENING
DISCHARGE
UNION
SUCTION
Figure 1
Install, ground and wire accord-
ing to local and National Electri-
cal Code requirements.
Install an all leg electrical power
disconnect switch near the
pump.
Disconnect electrical power be-
fore installing or servicing pump.
3