Tabla de contenido
GB
Replacing carbon brushes
•
Replace both carbon brushes at the same time.
•
Regularly check the carbon brushes for wear and defects.
•
Always replace worn-out carbon brushes.
•
Always keep the carbon brushes clean, and make sure that neither brush is obstructed.
•
Open the machine to inspect/replace the carbon brushes.
•
Remove and replace the carbon brushes if necessary.
•
Reassemble the rear handgrip.
Cleaning
Clean the machine casings regularly with a soft cloth, preferably after each use. Make sure that
the ventilation openings are free of dust and dirt. Remove very persistent dirt using a soft cloth
moistened with soapsuds. Do not use any solvents such as gasoline, alcohol, ammonia, etc.
Chemicals such as these will damage the synthetic components.
Lubrication
Fig.G
•
Regularly grease the hammer drill shaft.
•
Regularly check the grease-level inside the machine:
•
Remove the grease cap (12) on top of the machine (Off)
•
Remove also the second cap (with 4 notches)
•
Now you can see the rotating parts inside the machine: there should be grease on the
moving parts.
•
If necessary put some grease into the hole.
•
Place the cap onto the hole and tighten it again.
•
Mount the grease cap again (On)
Faults
Should a fault occur, e.g. after wear of a part, please contact the service address on the
warranty card. In the back of this manual you find an exploded view showing the parts that can
be ordered.
Environment
To prevent damage during transport, the appliance is delivered in a solid packaging which
consists largely of reusable material. Therefore please make use of options for recycling the
packaging.
Faulty and/or discarded electrical or electronic apparatus have to be collected at
the appropriate recycling locations.
Warranty
For the conditions of warranty, please refer to the separately provided warranty card.
10
ROTERENDE BOREHAMMER
Tallene i den følgende tekst korresonderer med afbildningen på side 2 - 4.
Læs denne betjeningsvejledning nøje, før maskinen tages i brug. Sørg for at vide,
hvordan maskinen fungerer, og hvordan den skal betjenes. Vedligehold maskinen i
overensstemmelse med anvisningerne, og sørg for, at maskinen fungerer korrekt.
Opbevar denne vejledning og anden vedlagt dokumentation sammen med
maskinen.
Påtænkt anvendelse
FBH-1100K er beregnet til at bore huller i murværk som mursten, beton og lignende
materialer. Desuden kan maskinen bruges som nedrivningshammer sammen med de SDS
koldmejsler, der følger med maskinen. Maskinen er under ingen omstændigheder påtænkt til
andre formål.
Undersøg venligst maskinen og tilbehøret for transportskader.
Indhold
1.
Information om maskinen
2.
Sikkerhedsanvisninger
3.
Betjening
4.
Vedligeholdelse
1. INFORMATION OM MASKINEN
Tekniske specifikationer
Netspænding
Frekvens
Nominel effekt
Rotationshastighed, uden belastning
Slaghastighed
Maks. bordiameter
Beton
Stål
Træ
Vægt
Lpa (lydtryksniveau)
Lwa (lydeffektniveau)
Vibrationstal
Produktinformation
Fig. A + F
1.
Regulering af rotationshastighed
2.
On/Off-kontakt
Ferm
Ferm
DK
230 V
50 Hz
1100 W
750/min
2920/min
Ø 30 mm
Ø 16 mm
Ø 40 mm
6,0 kg
90,7 dB(A)
105 dB(A)
4,3 m/s
2
75
Tabla de contenido
