DWT KGS16-210 Р Serie Manual Original página 22

when controlling the power tool� Therefore, proper
holding can reduce the risk of accidents or injuries�
Service
• Have your power tool serviced by a qualified
repair person using only identical replacement
parts. This will ensure that the safety of the power tool
is maintained�
• Follow instruction for lubricating and changing ac-
cessories�
Safety guidelines during
power tool operation
Before commencing operation
• Use the power tool only for cutting material recom-
mended by the manufacturer�
• Before use, place the power tool on a steady hori-
zontal base�
• Use saw blades with maximum allowable rotation
speed higher than that of the power tool spindle� Saw
blades must be used in accordance with manufactur-
ers' recommendations� Do not use saw blades which
fail to meet the technical requirements contained in
this manual�
• The saw blade arrow must always point in the same
direction as the guard cover arrow�
• Use sharp and undamaged saw blades only� Cracked,
dented or dull saw blades have to be replaced�
• Do not use saw blades with dimensions (outside and
mounting diameter) different from recommended�
• Do not use saw blades made of high-speed steel�
• Never use other types of cutting blades (abrasive,
diamond, etc�) for this power tool�
• Ensure that all devices preventing accidental touch-
ing of the saw blade are properly mounted, functional
and in perfect order�
• Never work with protection devices dismounted� Dam-
aged protection devices must be replaced immediately�
• During operation never fix (bind, wedge, etc.) the
sliding guard cover open�
• Avoid blocking of the sliding guard cover or its clogging
with sawdust If this is the case switch off the power tool,
fix the malfunction and only then continue operation.
• Do not use the power tool with a damaged insert�
• Before you start work, ensure that the saw blade
does not touch the turntable at any tilt angle�
• Remove all nails or any other metal objects from
blanks before cutting�
During operation
• Never stand on the power tool - if it turns over or if
you accidentally touch the saw blade, you can be seri-
ously injured�
Keep your hands at a safe distance from
the saw blade. Dangerous areas are
marked with a special sign.
• During operation watch the position of a power cable
(it should always be positioned behind the tool)� Do not
allow it to whip around your legs or arms�
• Never start cutting until the saw blade reaches its
full speed�
• When processing small blanks, use clamping devic-
es. If the blanks are too small to be fixed properly - do
not process them�
• Always process only one blank - this is the only way
to fix it properly.
• While processing long blanks use the clam ping de-
vices and be sure to provide a support under the long
end of the blank� Never make a third person hold the
working blank�
• After cutting remove all blank waste-ends from the
turntable surface - they may block up the saw blade, or
the rotating saw blade may throw them at a high speed
at the user�
• Never keep your hands behind the saw blade (when
holding blanks, removing waste ends, etc�)� In this
case the distance between the saw blade and your
hands is too small - and there is an increased risk of
serious injury�
• Never remove sawdust or blank waste-ends while
the power tool motor is running�
• It is necessary to observe the applicable rules while
cutting with traversing�
• While cutting grooves, it is necessary to keep an eye
on the saw blade - it can get stuck in the material being
machined�
• If during operation the saw blade gets stuck in the
blank or is blocked by the waste-ends, immediately
switch off the power tool and only then eliminate the
cause of the saw blade failure�
• Never treat workpieces containing asbestos�
• Do not use the power tool to cut firewood.
• Avoid stopping the power tool motor when under
load�
• Avoid overheating your power tool, when using it for
a long time�
• If your power tool is equipped with a kerf indicat-
ing laser, observe the necessary safety measures�
Never look at the beam or point it at other people or
animals - if the la ser beam strikes the eyes, it can
damage the eyesight�
After finishing operation
• The power tool can be removed from the workplace
only after the saw blade has been switched off and
stopped completely�
• Never try to slow down the inertial rotation of the
saw blade with the spindle lock or by applying effort
to the saw blade lateral surface� If you use the spindle
lock for this purpose, the power tool will fail and your
warranty will be cancelled�
• The saw blades can get very hot during operation -
do not touch them until they have cooled down�
Following symbols are used in the operation manual,
please remember their meanings� Correct interpreta-
tion of the symbols will allow correct and safe use of
the power tool�
Symbol
English
22
Symbols used in
the manual
Meaning
Serial number sticker:
KGS ��� - model;
XX - date of manufacture;
XXXXXXX - serial number�